8 Best 85 Inch TV Mount | Picks That Hold a 100 Inch Screen Tight

Check Price on Amazon

Pre-assembled muscle for screens up to 110 inches, with a tool-free tilt you can adjust by hand.

If your TV is a true giant, this is the mount that carries it. It supports 37 to 110-inch screens up to 170 lbs, and buyers report hanging 160 lb, 100-inch Hisense sets on it without drama—some even note it holds up to 200 lbs in practice, though 170 lbs is the stated rating. The max VESA of 800 x 600mm covers the biggest mounting patterns on the market, so it beats the Mounting Dream above on both size reach and weight capacity (170 lbs vs 132 lbs).

The standout feature is the tool-free tilt, adjusting from -15° to +5° with no wrench required, which makes glare fixes a one-hand job. The arms extend to 23.19 inches and retract to a slim 2.68-inch profile, with a generous ±60° swivel for open-plan rooms. It installs on 8 to 24-inch wood studs without anchors, and concrete or brick just need anchors the brand sends on request.

Quality and sturdiness dominate the owner feedback, and the pre-assembled design with a bubble level and paper template gets you mounted in under 30 minutes. The catch is the sheer weight of the thing—buyers consistently say you need two or even three adults to lift the TV onto it. The included level is also a weak point; several owners swapped in their own.

Check Price on Amazon

The long-reach specialist that swings an 85-inch screen 90 degrees around a corner.

Most mounts extend a foot or two, but this Perlegear rockets out to a 40.1-inch reach—more than double the Mounting Dream’s 18.3 inches. That is the number that matters for corner installations or built-in cabinets, where the TV must clear furniture and angle toward the seating area. It handles 42 to 97-inch TVs up to 150 lbs with a 800 x 400mm max VESA, so an 85-inch panel sits comfortably within its range.

The ±90° swivel is the other headline feature. Buyers describe turning a 55-inch TV 90 degrees to the wall on a porch, and the same freedom applies to an 85-inch screen in a corner. The tilt adjusts +5°/-15° for glare, and there is ±4° of post-install leveling so you can correct a slightly crooked wall without redrilling. Cold-rolled steel plus a wide wall plate keep it rigid even at full extension, backed by a 4x load test and a 6,000-cycle durability test.

Installation is a tidy three-step process with a drilling template and bubble level included, and owners note it retracts to just 3.7 inches when you want it flush. The real-world note: lifting a large TV onto long arms is awkward, and reviewers advise a second person. On thin concrete walls you will need Tapcon screws, which the brand’s support can help source.

Check Price on Amazon

A touch-to-adjust mount that tucks an 85-inch screen to just 2.5 inches off the wall.

This SANUS is for the buyer who wants a clean, flush look without giving up motion. It holds 42 to 90-inch TVs up to 125 lbs, which covers an 85-inch screen in most cases, and retracts to a very slim 2.5 inches from the wall—thin enough that it reads as a floating screen. The stainless steel build has space behind it for small streaming devices, so you can hide a stick or box out of sight.

The headline spec is the tilt range, reaching up to 35 degrees, which is the most flexible of any pick here for cutting ceiling-light glare from a high mount. It extends 22 inches out, and owners praise how smoothly it moves and tilts in all directions with zero sag or wobble, even on curved TVs. The kit is all-inclusive with a hardware bag, drilling template, and pre-assembled parts, aiming for a 20-minute install on 16-inch studs or concrete.

Build quality and sturdiness dominate the feedback, and it is UL listed and safety tested. The mixed feedback depends on installation alignment—some found it very easy, others needed extra patience getting the TV level. It also officially supports 16-inch stud spacing, so measure your wall before committing.

Check Price on Amazon

Reinforced six-arm strength rated for 250 lbs lets an 85-inch OLED sit rock-steady.

If your TV is heavy and you want serious margin, this MOUNTUP is the value-overkill pick. It carries 50 to 110-inch screens up to 250 lbs—the second-highest rating here—with a 800 x 600mm max VESA, and its six-arm reinforced alloy steel design is built for screens like 85, 90, and 100 inches. Owners mention it handled a 250 lb test and supports a 120 lb, 86-inch TV without breaking a sweat.

The design returns to a slim 1.65 inches from the wall when retracted, so you get both muscle and a sleek profile. The tilt runs +15°/-15° to fight glare, the swivel reaches ±45°, and the arms extend 19.9 inches for open-plan seating. It fits 12, 16, 18, and 24-inch studs—a wider range than most—and can mount on wood, concrete, or brick, though drywall alone is off the table.

Quality and installation speed are what owners praise, with a pre-assembled bracket, labeled hardware, a bubble level, and cable ties all in the box. The honest gripes: a four-point grip and tilt-adjusted via six nuts means setup is more involved than tool-free designs, and some units arrive with damaged boxes. As one buyer put it, this is “much better and easier to rotate” than cheaper brackets while holding the same weight.

Check Price on Amazon

A 255 lb-capable mount with a built-in power strip that hides every cable behind the screen.

This is the mount for the buyer obsessed with a clean, cable-free wall. Perlegear builds a power strip directly into the bracket—3 AC outlets and 2 USB ports on a 7.87-foot cord—so your TV, game console, and streaming stick all plug in right behind the panel. No separate power strip, no dangling wires, just a tidy install that also frees up your wall outlets.

It is also the strongest pick in this list by rated weight, holding up to 255 lbs on screens from 55 to 120 inches, with a 900 x 600mm max VESA that covers virtually every large TV. The 20% thicker steel and reinforced wall plate keep it stable even fully extended, tested with a 4x load test and 6,000-cycle test. Owners have mounted 107 lb and 85-inch TVs on it and report zero wobble or sag.

The flexibility is first-rate: extend 22 inches, swivel ±65° to face any seat, tilt +5°/-15° for glare, and retract to just 3 inches. It installs on 16, 24, or 32-inch studs, which is the widest stud compatibility here. Quality and ease of installation dominate the feedback, with a pre-assembled design and hinged straps that make the TV hang straightforward—though it still needs two people. The one repeated note: the swivel can feel tight at first.

Check Price on Amazon

A tank-like steel mount with a 28-inch reach and a swivel that rotates up to 88 degrees.

The Kanto FMX3C is built like the engineers over-engineered it on purpose. It holds 37 to 90-inch TVs up to 150 lb (68 kg) with a 700 x 500mm max VESA, and the solid steel construction with heavy-duty lag bolts is the reason owners describe it as “built like a tank.” It extends a generous 28 inches from the wall and swivels 45° to 88° left or right depending on screen size, so an 85-inch panel can face almost any seat in the room.

The tilt runs +5°/-15° to cut glare, and the cable management tucks cords out of sight for a clean look. It fits 16 or 24-inch studs, which broadens your wall options, and the install is straightforward with a wall template and an organized bolt pack. Owners have mounted a 98 lb, 70-inch Sony and even a 102 lb plasma on it with zero sag at full extension, and a 28-inch extension gives you real flexibility for awkward layouts.

Quality and sturdiness are the overwhelming consensus, and the 5-year warranty plus US-based support add confidence. The weight (11.58 kg) is the recurring note—this is a heavy mount, so solo install is possible but a second person makes the TV hang far safer. There is no vertical adjustment, so measure your placement height carefully before you drill.

Check Price on Amazon

The heaviest-duty pick here, rated for 275 lbs with a 39-inch reach and 360° rotation.

This is the mount for the buyer going all-in on a massive home theater. The Beast handles 60 to 110-inch TVs up to 275 lbs—the highest weight rating and the second-longest extension (39 inches) in this entire list—with a 800 x 600mm max VESA. Owners have hung 100-inch TVs on it and, in one memorable test, a 260 lb person hung from the fully extended arm to prove it was solid.

The dual articulating arms give full tilt, swivel, and 360° rotation, so an 85-inch screen can eliminate glare, reduce neck strain, and face any seat from the couch to a conference table. It is 4x safety tested, rated to hold four times its 275 lb limit at 1,100 lbs, with reinforced coated steel and stainless steel hardware. A sliding wall plate lets you center the TV even when studs are not perfectly aligned, and integrated cable management hides every cord.

Quality, adjustability, and holding strength are what owners rave about, with brass bushings delivering smooth articulation. The trade-offs are real: at 43.7 pounds, this is a beast to handle, and owners say you need 2-3 people for the install. Plastic anchors fail in brick or concrete, so use sleeve anchors there, and the stiff movement takes some muscle on first use.