9 Best 3.7 V Battery And Charger | Stop Tossing Dead Cameras

Check Price on Amazon

A single high-capacity cell for Minolta and Zoom recorder owners who want a wall-socket charger.

This is the kit for a very specific job: powering a Minolta MN35Z, a Zoom BT-03 or BT-03 B battery, a Zoom Q8 or Q8N recorder, or a Bell & Howell B35HDZ camera. The cell runs 3.7V and 2300mAh, which sits just under the 2400mAh Batmax above but well above the 1000mAh Newmowa NB-5L. For a recorder running continuous audio or video, that headroom matters — you are not swapping cells halfway through a session. The charger is the AC wall type with foldable flat pins, so it stores flat in a bag and plugs straight into a socket without a cable. Input is rated AC 100~240V at 50~60Hz with a DC 4.2V 600mA output, which means it works on overseas mains voltage as well as domestic.

Owners of these Minolta and Zoom bodies tend to praise it for doing exactly what a replacement battery should — dropping in, taking a charge, and powering the device as advertised. The one honest caveat that surfaces repeatedly is that it is a single-battery kit with no USB option, so if you want to charge on the move from a power bank, this charger cannot do that. It is a wall-socket charger by design, and it comes with only the AC unit — no car adapter and no European plug adapter in the box, both of which are sold separately. That is not a fault, it is a scoped design choice, and for a recorder that lives on a desk it is the right one.

The trade-off to weigh is simple. The AC-only charging and the single-cell pack make this a home-studio kit rather than a travel one. If your Minolta or Zoom gear stays on a desk, the foldable wall charger is convenient and the 2300mAh cell gives you a long session. If you shoot on location and need to top up from a USB power bank, one of the USB-charging kits on this list will suit you better.

Check Price on Amazon

The highest-capacity hobby pack here, feeding low-draw boards for well over a day.

This is the pick for tinkerers running Meshtastic nodes, RAK19007 boards, or other small electronics off a single cell. Two 3000mAh Li-polymer batteries with 3.7V ratings and a PH2.0 connector come with a USB charging cable that carries a status LED and smart IC control. The 3000mAh capacity is the top figure in this entire roundup, and it shows: buyers report a Meshtastic node running 1.4 days per charge. If your board draws a steady trickle — say 450mA — a 450mA board draws 4 hours and 20 minutes from a single cell, which is the sort of number you can plan a field session around.

The pack ships with a built-in protection board guarding against overcharge, over-discharge, over-current, overheating, and short circuits, and the batteries comply with UN 38.3 and CE standards. That protection circuitry matters here because a lipo cell in a DIY build can spend weeks unattended. Reviews from board builders are largely positive, with the caveat that the connector is a PH2.0 — a specific two-pin plug — and some builders found their board needed a different size entirely. One reviewer noted plainly that the pigtail was too big and the polarity was reversed for a Heltec v4 board, adding: “I like the USB charger though.” The lesson is not that the battery is bad — it is that in hobby electronics, connector matching is your responsibility, and the listing tells you exactly what shape you are getting.

The genuine appeal of this kit is capacity per cell in a small footprint. At 3000mAh it outlasts the 1100mAh Meshnology pack below on paper, and the PH2.0 connector is one of the more common plugs on development boards. Read the connector label against your board before buying, keep a short adapter on hand if you are between sizes, and this becomes a great-value pair for a projects bench.

Check Price on Amazon

A slim single-cell kit that wakes older camcorders without any extra bulk.

The NP-6L is for anyone still using a compact digital video camera — the DC 311, 302, 402, 403, and 406 external battery chargers are named explicitly — and for point-and-shoots that live on the CAS. NP-6L format. The cell runs 3.7V and 700mAh, which is the smallest capacity in this roundup. That is not a flaw for this class of device: these older camcorders draw very little, and a small cell keeps the whole thing light. The charger takes a 5V input and outputs 4.2V, and it comes with a USB-C cable in the box, so it charges from a modern power block without hunting for an old adapter.

This kit earns its place through the narrow fit it satisfies. Many of these older camcorders use proprietary cells that are no longer sold in original form, and owners describe this replacement as a perfect fit for cameras eight or more years old — one that installs with a directional arrow and holds a charge over long sessions. That is exactly what keeps aging gear out of a drawer.

The honest caveat here is fit precision. This cell is built to the CAS. NP-6L shape, and not every camera that takes a similar-looking battery will accept it — some users with a Minolta MND23 reported the battery would not lock into place, which is a shape mismatch, not a defect in the cell. The takeaway is simple: if your camera lists CAS. NP-6L compatibility, this drops in cleanly and does the job. If it takes a slightly different format, move on.

Check Price on Amazon

The Canon ELPH revival kit — a small extra-capacity cell with a charger that shows charge as a percentage.

This one is aimed squarely at the Canon PowerShot crowd: the ELPH 100 HS, 300 HS, and 310 HS, along with the SD1000, SD1100 IS, SD1400 IS, SD750, SD400, SD200, SD30, SD300, SD40, SD450, and SD630 bodies. The cell is a 3.7V unit rated 1080mAh, which is a step up from the 900mAh D&F pack below and what makes it practical for a point-and-shoot you want to carry all day. The 1080mAh also lines up with the Batmax 2400mAh as the meaningful capacity jump on this list — you carry more shots per charge than the smaller-body kits.

The charger here is the standout feature: it has both a micro-USB port and a USB-C port, so you can top up with whichever cable you have closest to hand. It also carries an integrated LED display that shows how much charge the battery holds as a percentage, rather than the blink-or-solid bars most chargers settle for. In practical terms, that means no guessing when you are packing for a trip. The charging output is rated 4.2V/600mA from a 5V/2A input — a modest, safe rate for a cell this size. Owners who use it for hiking and camping like that the charger runs from a wall block or any USB power source, making it a light piece of travel kit.

There is one fit note worth reading carefully. The manufacturer lists this battery as fully compatible with a long list of Canon cameras and gives it a 12-month warranty, but a small number of users with an original Canon battery found their specific OEM cell did not seat cleanly in the charger. That is a charger-slot quirk rather than a battery problem, and the included cells themselves charge and run fine. If you own a genuine Canon NB-4L and plan to recharge it in this pack’s charger, treat it as a secondary use — the bundled Pickle Power cells are the primary fit. As one camera owner put it: “they were compatible, they charge super quick and fit perfectly with camera!”

Check Price on Amazon

Four 900mAh action-camera cells and a dual-slot charger — the spare-battery vault.

If you shoot action-camera footage and hate stopping to swap a dying cell, this is the kit that ends the problem. You get four 900mAh 3.7V Li-ion batteries plus a dual-slot charger that tops up two cells at once, cutting wait time between sessions. The pack is built for the SJCAM SJ4000, SJ5000, SJ6000, and M10 action cameras, and each cell weighs just 0.09 kg — the sort of featherweight that disappears in a camera bag. The dual-slot charger runs on a USB cable with a 5V input and 1A current rating, so it works off a power bank like any other USB device.

Owners use this kit for one clear job: getting old action cameras running again. Many find the original cells have swollen after years in storage and these replacements — which arrive not swollen — bring the camera back to life. Runtime reports are decent for this class: owners mention about two hours of steady recording per cell, and compatibility extends to 4K Ultra HD action cameras that share the same cell format. The charger is the practical win here, since charging two cells at once means you always have a spare ready. Stacking four cells in total means a full day of shooting without ever being tethered to a wall.

The one recurring gripe is cosmetic rather than structural: the stickers on the cells can slip off over time as the adhesive ages, which is a minor annoyance on an otherwise solid set of cells. If you are the kind of shooter who labels every battery, budget a minute to re-mark them. Otherwise this remains a genuinely useful multi-pack: four cells, a two-at-once charger, and a form factor built for the action-camera crowd.

Check Price on Amazon

A travel-first two-battery Canon kit with a charger you can run from a car or power bank.

This kit is aimed at Canon NB-5L users — think older PowerShot compacts where the original cell has given up — and it delivers a complete backup package: two 3.7V batteries at 1000mAh each, one USB charger, and a micro-USB cable. The capacity is the modest figure here, and against the Batmax 2400mAh it is dramatically smaller at 1000mAh — a real gap in shots per charge for anyone comparing cells side by side. Where this one earns its keep is portability. The charger runs off a common USB input, so a wall adapter, a car charger, or an external battery all work. The LED turns red while charging and green when the cell is full, so you always know the state at a glance.

The other thing owners consistently mention is the packaging and build quality. The kit arrives in multiple layers of wrapping and boxes — over-engineered for a battery, but a sign the manufacturer takes care. The protection circuitry guards against over-charging, short circuits, high temperatures, and surges, and the build uses a fire-resistant construction. On the compatibility front, the listings and reviews mostly agree that it drops into NB-5L cameras cleanly, though a handful of buyers found the battery connection did not match their particular device, which is a reminder to confirm your model before ordering.

The honest read: this is a capable travel kit, not a big-capacity one. The two included cells are 1000mAh each, which is enough for a day of casual point-and-shoot use but not for a long continuous session. If you shoot sparingly and want a charger you can toss into any USB port on the road, the combination works well. If you need maximum runtime per cell, look at the higher-capacity kits above. As one buyer found: the listing said micro-USB, but the charger actually ships with a USB-C connection — a nice surprise that makes it more future-proof than the spec sheet suggests.

Check Price on Amazon

Four 1100mAh cells on Micro JST plugs — the volume pick for small electronics fixes.

This pack is for the person with a drawer full of small devices that all need the same cell. Four 1100mAh 3.7V Li-polymer batteries ship together, each weighing 1.06 ounces, with a Micro JST 1.25 connector — a small two-pin plug common on project boards, drones, and RC vehicles. A USB charging cable with a 300mA output and reverse polarity protection is included, so you can top up a cell from any USB port. If your project fits the Micro JST 1.25 standard, four cells at 1100mAh each means backups for a long time to come.

Owners use the pack for exactly the sort of repair that would otherwise mean a landfill trip. Two of these fit neatly into a 4×AA compartment, which opens up conversions from disposable AA power to a rechargeable setup. Others have used a cell to repair hearing-protection headphones or replace a failed battery in a compact speaker. The chargers are described as slow — the 300mA output is a trickle rate, so a full charge takes a while — but they are reliable, and the protection board on each cell handles the safety work. If you are patient with charging, the kit does what it says.

The one thing to check before ordering is the connector and capacity match. The 1100mAh figure is smaller than the 3000mAh Meshnology pack above, so if you need a single cell for a long-running node, that higher-capacity option is the better buy. If you want several small cells at a low cost for a range of little builds, this four-pack is the smarter spend. Just confirm your board takes a Micro JST 1.25 plug, and you are set.

Check Price on Amazon

The high-capacity pair for RC and drone builders who need long runtimes with a Micro JST plug.

Two 3000mAh Li-polymer cells at 3.7V, each weighing 1.76 ounces, ship with a USB charging cable and a Micro JST 1.25 connector. The name of the game here is runtime for remote-control vehicles and small development builds — the same 3000mAh class as the PH2.0 pack above, but on a Micro JST 1.25 plug instead. If your drone, RC car, or Arduino-style board needs those particular connector pins and a big reservoir of charge, this two-pack delivers it. The charging cable carries an intelligent IC and reverse polarity protection, so a miswired connection is defended against.

The kit earns credit for durability in real use. Customers note roughly 30 charge cycles with no performance or charging issues — the kind of longevity a hobbyist wants before trusting a cell to an expensive build. The connector decision is the main thing to get right: some boards and Miyoo-style devices take this exact connector family, and this kit is a comfortable fit for them.

One area to plan around is the case. Builders who matched this battery to a printed enclosure sometimes found the case needed a little persuasion — one buyer mentioned the front panel arrived slightly warped and needed gentle heat and pressure to clamp shut cleanly over the cell. It is typical of 3D-printed parts rather than the battery itself, but note if you are pairing the pack with a custom housing. Order the right connector, allow a moment to fit your enclosure, and this pair gives you two full-capacity 3000mAh cells for serious runtime.