What Size Drill Bit Is 33/64? | Decimal & Metric Facts

A 33/64-inch drill bit measures exactly 0.5156 inches (13.1 mm) and sits between the 1/2-inch and 17/32-inch sizes in the standard fractional drill series.

The 33/64″ bit is part of the ANSI-standard fractional series that runs in 1/64-inch increments from 1/64″ up through 1″. It measures 0.5156 inches in decimal form — 0.515625 to be precise — with a metric equivalent of 13.097 mm, commonly rounded to 13.1 mm. This bit is not a number or letter gauge; it’s exclusively a fractional inch size. Its position in the series falls between 1/2″ (0.5000″) and 17/32″ (0.5313″). Whether you’re working on a plumbing fixture, a piece of machinery, or a precision tapping job, knowing the exact dimensions of this bit down to the thousandth of an inch matters. Below you’ll find the complete specifications, the jobs it handles, and the common mistakes that trip up even experienced machinists.

What Exactly Is A 33/64 Drill Bit?

The 33/64″ bit is a right-hand cutting tool with two flutes and a standard 118° point angle. It’s typically made from high-speed steel (HSS) with a black oxide finish and conforms to ANSI B94.11M-1979, the standard for jobber-length straight-shank twist drill bits. The diameter tolerance for this size is -0.0012 to +0.0000 inches, meaning the bit can be slightly undersized but never oversized. The shank diameter matches the cutting diameter on standard jobber-length bits, though reduced-shank versions exist for use in smaller chucks.

Specification Value
Fractional Size 33/64 inch
Decimal Inch 0.5156 in (0.515625 exactly)
Metric Equivalent 13.097 mm (≈13.1 mm)
Point Angle 118°
Flutes 2
Cutting Direction Right Hand
Common Material High Speed Steel (HSS)
Common Finish Black Oxide
Diameter Tolerance -0.0012 to +0.0000 in

This bit is widely used in US construction, plumbing, and American-made machinery where drawings use inches. In metric-dominant regions (Europe, Asia), the 13.1 mm specification is preferred and the 33/64″ size is rarely stocked. The bit is typically sold individually — most consumer drill sets skip this size entirely, jumping from 1/2″ straight to 17/32″.

What Is A 33/64 Drill Bit Used For?

The 33/64″ bit handles steel, stainless steel, cast iron, non-ferrous metals, superalloys, and titanium. It’s also used as a tap drill for specific UNC and UNF thread sizes — always confirm with a tap drill chart before threading. When working with US-dimensioned fasteners or inch-based drawings, the imperial 33/64″ bit is the right call. For European or Asian equipment, use the closest metric equivalent.

Speaking of metric substitutes: a 13 mm bit (0.5118″) is 0.0038 inches undersized — too tight for precision tapping or press-fit work. A 13.5 mm bit (0.5315″) is 0.0159 inches oversized. For any job where the drawing specifies 33/64″, the exact fractional bit is the tool to reach for.

Common Mistakes To Avoid

Confusing 33/64 with 17/32. The 17/32″ bit measures 0.5313 inches — 0.0157 inches larger. Using it where 33/64″ is called for produces an oversized hole that compromises thread engagement and press-fit stability.

Assuming a 13 mm bit is an exact substitute. At 0.5118 inches, it’s nearly 0.004 inches undersized. Passable for loose clearance holes, but not for tapping or press-fit applications where precision matters.

Assuming it’s in your set. Most standard drill sets skip 33/64″. Always verify before starting. If you need to buy one, our roundup of the top 33/64 drill bits covers the best individual options to add to your kit.

Checking size on a worn bit. If the marking is faded, clean the cutting edges and measure across the widest point of the flutes with digital calipers. You should read 0.5156 inches (13.097 mm). Don’t measure the shank — reduced-shank bits have a smaller shank than the cutting diameter. Also confirm the bit material is suitable (HSS is standard for steel; superalloys may need carbide) and that it’s a right-hand bit before drilling.

FAQs

Is 33/64 the same as 17/32?

No. 33/64 equals 0.5156 inches and 17/32 equals 0.5313 inches — a difference of 0.0157 inches. They are not interchangeable; using the wrong size produces an incorrectly sized hole that may compromise your project.

Can I use a 13 mm bit instead of a 33/64?

A 13 mm bit (0.5118″) is 0.0038 inches undersized. For non-critical clearance holes it may work, but for tapping, press-fit, or any precision application, use the exact 33/64″ bit or its true metric equivalent of 13.1 mm.

Where is a 33/64 drill bit most commonly used?

It’s standard in US construction, plumbing, and American machinery where inch-based engineering drawings are the norm. It also serves as a tap drill for certain UNC and UNF threads and can drill steel, stainless steel, cast iron, and other metals.

References & Sources

  • Wikipedia. “Drill Bit Sizes.” Comprehensive reference for fractional, number, and letter drill bit dimensions and industry standards.

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.