A screened balcony keeps bugs out or adds privacy, and you can finish the job in a weekend with either a screen track system or fabric privacy panels.
Balcony screening comes down to one choice: insect-proof mesh or visual privacy. The first uses a screen track system with polyester or fiberglass mesh stretched into aluminum extrusions. The second uses fabric privacy screens with eyelets secured to the existing railing with zip ties. Both methods are DIY-friendly, require no permanent structural changes, and cost significantly less than hiring a contractor. The table below shows which materials fit which goal.
Screen Track vs. Fabric Privacy Screens
Choose the right system for what you want: bug protection or total visual blockage. Screen track systems are the standard for insect screens, while fabric panels are better for privacy and windbreaks.
| System | Best For | Key Materials |
|---|---|---|
| Screen Track | Insect protection, ventilation | Aluminum extrusions, polyester mesh, spline, spline tool |
| Fabric Privacy Screen | Privacy, windbreak, shading | Fabric with eyelets, zip ties (cable ties), grommets |
| DIY Staple Gun | Quick temporary fix | Mesh roll, staple gun, staples (9×16) |
How to Screen a Balcony: The Two Best Methods
Both methods start with accurate measurements and a clean railing. Your choice determines the tools and steps that follow.
Method 1: Screen Track for Bugs
This is the permanent solution for keeping insects out while maintaining airflow. The official guide from screenporch.com details the process: install aluminum extrusions around the opening, then stretch mesh into the groove and lock it with spline.
- Measure and cut width extrusions. Measure the inside width of your balcony opening. Cut the aluminum extrusions with a blade rated for aluminum or plastic. A tight fit is essential.
- Pre-drill mounting holes. Place the first hole 1 inch from each end, then space additional holes 12 inches apart.
- Measure and cut height extrusions. Repeat the same steps for the vertical extrusions. Test-fit before mounting.
- Mount the extrusions. Install the width and height pieces, making sure they align perfectly at the corners.
- Roll in the mesh. Lay the polyester or fiberglass mesh over the frame. Use a screen spline tool to press the spline into the extrusion groove, securing the mesh tightly. Work from one side to the other to prevent slack.
- Trim excess material. Run a utility knife along the top edge of the extrusion. Cut carefully to avoid nicking the spline.
Method 2: Fabric Privacy Screen
This method adds visual privacy and wind protection without drilling into walls or floors. The germes.com guide shows how to attach a pre-made fabric screen directly to your existing railing using eyelets and zip ties.
- Inspect the railing. Remove loose objects and check for sharp edges that could tear the fabric. Make sure the railing is securely fastened.
- Position the fabric. Attach the top and bottom eyelets first, straightening the fabric until it’s taut.
- Secure all eyelets. Fasten every eyelet to the railing using cable ties, cord, or any provided hardware. Do not drill into walls or the floor.
- Apply even tension. The fabric should be tight enough to avoid wind flapping but not overstretched, which can tear material or pull out eyelets.
- Leave drainage clearance. Keep the bottom edge 3–5 cm above the floor to allow rainwater to drain and prevent the fabric from staying damp.
If you’re ready to buy a finished product instead of building from scratch, check out our roundup of the best balcony screen doors for pre-built options.
Common Mistakes and How to Avoid Them
Most problems with balcony screening come from skipping the prep work or rushing the installation. Keeping an eye on these pitfalls saves time and materials.
- Inaccurate measurements: Double-check every opening dimension before cutting extrusions. A poor fit wastes material and leaves gaps.
- Cutting too deep: When trimming mesh with a utility knife, stop short of the spline to avoid cutting the seal that holds the screen tight.
- Over-tightening fabric: Stretching a privacy screen too hard can tear the material or rip out the eyelets. Tension evenly, not forcefully.
- Blocking drainage: Never mount the fabric flush to the ground. The 3–5 cm gap is your best defense against mold and dampness.
- Ignoring apartment rules: Check your lease or HOA guidelines before installing anything that looks permanent. Many complexes have specific rules about balcony modifications.
FAQs
Can I screen a balcony without drilling holes?
Yes, fabric privacy screens with eyelets and zip ties attach directly to the railing and require no drilling into walls or floors. This makes them ideal for renters and temporary setups.
How long does a balcony screen last?
A properly installed screen track system using polyester mesh can last 5–10 years with basic care. Fabric privacy screens typically last 2–4 years depending on sun and wind exposure.
What’s the cheapest way to screen a balcony?
References & Sources
- ScreenPorch.com. “How to Screen in a Balcony” Official DIY guide for screen track systems.
- Germes.com. “Balcony Privacy Screen Installation Guide” Step-by-step instructions for fabric privacy screens.
