A mil is a unit of thickness equal to one-thousandth of an inch (0.001 inch), the standard US measurement for plastic film and sheeting.
If you’ve shopped for plastic sheeting and seen “6 mil” on the label, that number refers to the material’s thickness — one-thousandth of an inch. Understanding what does mil mean in plastic sheeting helps you pick the right strength for your project, whether it’s a light painting tarp or a heavy construction vapor barrier. This guide explains the measurement, common thicknesses, and how to choose.
What Exactly Is a Mil?
A mil equals 0.001 inch — one-thousandth of an inch, not a millimeter. In metric terms, 1 mil works out to 0.0254 mm, and 1 millimeter equals about 39 mils. Thickness is also expressed in gauge, where 100 gauge equals 1 mil. That means a 200-gauge sheet is 2 mil and a 300-gauge sheet is 3 mil.
The mil-and-millimeter mix-up is the most common mistake people make. A millimeter is roughly 39 times thicker than a mil, so confusing the two can lead to buying sheeting way too thin or unnecessarily thick for the job. Common benchmarks help put it in perspective: a grocery bag runs about 0.5 mil, copier paper is roughly 4 mil, and a human hair is about 1 mil.
Common Mil Thicknesses and Their Best Uses
Different projects demand different thicknesses. Here is how the standard mil ratings break down by application:
| Thickness | Category | Best Uses |
|---|---|---|
| 1–2 mil | Light duty | Indoor painting, furniture covers, pallet wrapping, light equipment protection |
| 3–4 mil | Medium duty | Temporary curtains, light vapor barriers, general packaging, drop cloths |
| 6 mil | Heavy duty | Construction enclosures, vapor retarders under slabs, job site covers, lumber covers |
| 10 mil | Outdoor/industrial | Pond liners, remediation covers, barge liners, temporary walls, greenhouse plastic |
| 12–15 mil | Structural | Under-slab vapor barriers, foundation wall barriers, landfill covers |
| 20–24 mil | Heavy containment | Aquaponics liners, grain storage covers, hay covers, retention pond liners |
| 30–40 mil | Extreme containment | Oilfield pit liners, fish hatchery liners, root barriers, soil remediation |
For most construction and heavy-use jobs, 6 mil is the go-to thickness. For outdoor and industrial applications that face UV exposure, chemical contact, or wind loads, 10 mil and up provides the necessary durability. If you need to buy, our tested guide to the best 10 mil plastic sheeting covers top-rated options.
How to Measure Plastic Sheeting Thickness
Use a thickness gauge or micrometer to verify the actual mil rating, since manufacturing tolerances can cause variation. Place the tool at the sheet’s thickest point — for string-reinforced (scrim) sheeting, measure across the cross-section of the string lacing. Lock the micrometer and read each numbered division as 0.001 inch (1 mil).
Common measurement mistakes include checking only thin spots, which gives a lower reading than the sheet’s true rating, and assuming mil alone predicts strength — material composition also affects durability. Also, a 6 mil scrim-reinforced sheet is significantly stronger than standard 6 mil sheeting.
Matching the mil rating to your project’s conditions — indoor versus outdoor, light versus heavy use, short-term versus long-term exposure — is what separates sheeting that performs from sheeting that fails.
FAQs
Is a mil the same as a millimeter?
No. A mil is one-thousandth of an inch (0.001 inch), while a millimeter is about 0.039 inches — roughly 39 times thicker. Confusing the two is the most widespread mistake in buying plastic sheeting, and it can result in material far too thin for the job.
What mil plastic do I need for a vapor barrier?
For under-slab vapor barriers in foundations, 6 mil is the minimum standard in most building codes, and 12–15 mil is common for heavy-duty below-grade applications. Check your local building code, since requirements can vary by region and the type of soil or moisture conditions.
Does a higher mil always mean stronger plastic?
Generally yes, but material composition matters too. A 4 mil sheet made from virgin polyethylene can outperform a 6 mil sheet made from recycled material in tear and puncture resistance. Scrim reinforcement also adds significant strength regardless of the base mil rating.
References & Sources
- U.S. Environmental Protection Agency. “What Mil Plastic Is Considered Impermeable?” States EPA guidance on 6 mil for lead-based paint containment.
- AmeriCover. “What Is Plastic Sheeting Mil Thickness?” Explains mil as a measurement unit and common applications.
- Global Plastic Sheeting. “Mil Thickness Compared to MM (Millimeter) and Inches” Provides conversion data between mils, inches, and millimeters.
