What Is Step Flashing on a Roof? | Water Barrier for Sidewalls

Step flashing uses overlapping L-shaped metal pieces woven into each shingle course to create a watertight barrier where a sloped roof meets a vertical wall.

Understanding what is step flashing on a roof starts with the L-shaped metal pieces that make it work. Step flashing is a woven system of individual L-shaped metal pieces installed at every shingle course where a sloped roof meets a vertical wall, chimney, or dormer. Each piece directs rainwater onto the shingle below rather than letting it seep behind siding or into the wall assembly. The International Residential Code requires step flashing at all roof-to-sidewall intersections for asphalt shingle roofs.

What Makes Step Flashing Different From Other Flashing?

Unlike continuous flashing or counter-flashing, step flashing uses separate pieces woven into each shingle course. This creates a cascading water barrier that moves with the roof as it settles. Each piece must overlap the piece below it by at least 2 inches to maintain a continuous barrier. Every flashing unit also needs to be at least 2 inches wider than the shingle exposure.

Step flashing is commonly fabricated from aluminum, galvanized steel, or copper. Metal choice matters — copper against untreated wood or aluminum siding can cause corrosion without a separation layer. For contractors and homeowners comparing material options, our roundup of the best aluminum step flashing products covers top-rated choices and what to look for in each.

Spec Requirement
Shape L-shaped, 90-degree bend
Standard Size 5 x 7 inches (unfolded: 10 x 7)
Minimum Length 10 inches (254 mm)
Minimum Wall Height 5 inches
Minimum Roof Extension 5 inches
Piece Overlap 2 inches minimum
Common Materials Aluminum, galvanized steel, copper
Code Standard IRC, required at all sidewall intersections

Step Flashing Installation Sequence

Installing step flashing correctly means alternating each flashing piece with a shingle course, working from the bottom of the roof up. Nail the horizontal flange to the roof deck within 1 inch of the flashing’s upper edge — never nail the vertical flange to the wall. Roof and wall structures move independently, and a rigid attachment to the wall causes shingle buckling and sealant failure over time.

The first piece sits over the starter strip and aligns with the kickout flashing at the base. Secure it with two roofing nails, then lay the first shingle course to cover the horizontal flange. Repeat this alternating pattern up the roof. Kickout flashing at the base ensures water runs into the gutter instead of behind the siding, as GAF’s technical bulletin on proper flashing details.

Common Step Flashing Mistakes

Several installation errors consistently cause leaks. Overlapping pieces by less than 2 inches lets water slip past the barrier and into the wall. Nailing the vertical flange to the wall creates a rigid connection that breaks as the roof settles. Placing flashing too far above the shingle line prevents it from shedding water onto the shingle surface. Using a single continuous metal strip instead of individual stepped pieces traps water against the wall instead of channeling it away.

Missing kickout flashing at the base is another frequent problem — water runs straight behind the siding instead of into the gutter. When repairing old step flashing, always start at the topmost piece and work downslope, reinstalling from the lowest point to the highest to maintain proper overlap direction. Leave a slight gap between the shingle and the step flashing to allow drainage and prevent trapped moisture.

FAQs

Can you use roofing caulk instead of step flashing?

Caulk alone cannot replace step flashing because it lacks the physical water-shedding shape and the cascading overlap that directs water over each shingle course. Caulk dries out, cracks, and fails over time, while properly installed metal step flashing lasts decades. Use caulk as a supplemental seal at exposed nail heads, not as a primary flashing replacement.

Does step flashing go under or over siding?

Step flashing installs against the wall sheathing before the siding goes on. The vertical flange sits against the wall, and the shingles cover the horizontal flange. Siding then laps over the top edge of the flashing or a separate counter-flashing piece, creating a complete water barrier. Installing flashing over existing siding traps moisture and defeats the purpose.

How long does step flashing last?

Performance depends on correct installation — even premium materials fail if nailed to the wall or installed without proper overlap. Regular roof inspections catch issues before leaks develop.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.