Installing antique kitchen taps requires turning off the water supply, verifying sink hole spacing, and securing the fixture with mounting nuts and PTFE tape before connecting hot and cold lines—a straightforward manual task with the right preparation.
Antique kitchen taps transform a utilitarian sink into a period statement, but their installation differs from modern single-handle faucets. The process is a manual plumbing job with no electronics involved, but getting the hole configuration wrong or skipping seals can turn a quick project into a leaky headache. Here is exactly what you need to know before picking up a wrench.
What You Need to Know Before Starting
Antique taps come in two styles: pillar taps (two separate handles, two sink holes) and bridge-style taps (single spout with two handles, two or three holes with specific spacing). A standard modern sink with one hole requires an adapter plate. Measure your sink’s hole layout against the tap’s base plate before buying anything.
US and UK installations differ: US homes use shut-off valves under the sink with 1/2-inch flexible supply lines and compression fittings, while UK systems rely on an internal stopcock and 15mm pipes with isolation valves. Steps are the same, but hardware names change; some antique models require a compression fitting kit for proper water pressure connection. If still choosing, our roundup of the best antique kitchen taps can help match a style to your sink’s hole pattern and budget.
The Installation Sequence: Step by Step
The job proceeds in five phases. Work slowly and check alignment before fully tightening anything.
Step 1: Shut off the water and drain the lines. Locate shut-off valves under the sink (US) or the internal stopcock (UK). If unreachable, shut off the main supply. Open old taps fully to drain residual water, then place a bowl under the sink to catch drips.
Step 2: Remove the old faucet. Use an adjustable or basin wrench to unscrew retaining nuts from underneath. If stuck, wiggle gently; old putty and calcium deposits can lock it. Disconnect supply lines and scrape off remaining putty or caulk from the sink surface.
Step 3: Prepare the sink and new tap. Clean thoroughly. For pillar taps with threaded lower connections, wrap PTFE tape counter-clockwise around threads. If included, apply plumber’s putty into the putty plate groove. For single-hole antique taps, use the supplied rubber or plastic gasket instead of putty.
Step 4: Mount the new fixture. Insert tap pipes through sink holes with seals and gaskets. Position the tap evenly from above, then secure underneath with fixing nuts. Install any under-side gaskets, washers, and retaining plates per manufacturer’s diagram. Tighten retaining nut by hand first, then with a tool. Verify alignment before final tightening; do not over-tighten, as antique brass can deform under excessive force.
Step 5: Connect supply lines and test for leaks. Match hot (left) and cold (right) connections per US convention. Wrap new PTFE tape on threaded parts, hand-tighten supply lines, then give a final quarter-turn with wrenches. Turn water back on slowly. Keep taps open initially to release trapped air, then close them and check every connection for drips.
Common Mistakes That Cause Leaks
Four errors account for most failed installations. Reversed flow from swapped hot/cold supply lines—label them before disconnecting. Over-tightening mounting nuts can crack the sink basin or warp the tap base. Skipping the gasket or putty seal leaves a path for water seepage. Ignoring drainage means you discover a slow leak only after the cabinet is soaked.
Ensure your sink can support a heavy antique brass tap—cast fixtures can exceed ten pounds, and a thin stainless sink may sag without reinforcement. Confirm hole spacing: most bridge-style designs require three holes 8 inches apart; pillar taps need two holes at 4 or 6 inches. Measure twice before ordering.
FAQs
Do antique kitchen taps fit modern sinks?
Most require two or three holes; modern single-hole sinks need an adapter plate. Measure your sink’s hole layout against the tap’s base spacing before purchasing.
Can I install antique taps without a plumber?
Yes. The job is manual with no electrical requirements. If you can turn off a water valve and use a wrench, you can install these taps yourself—work slowly and check for leaks after turning water back on.
What tools do I need?
An adjustable wrench, basin wrench, PTFE tape, plumber’s putty or gaskets, putty knife, and washers. US installations use 1/2-inch flexible supply lines; UK setups use 15mm pipe and isolation valves.
References & Sources
- Home Depot. “How to Install a Kitchen Faucet.” Detailed installation guide for US standard fittings.
- Homebuilding & Renovating (UK). “Fitting a Kitchen Tap.” Covers UK plumbing conventions including stopcocks and 15mm pipes.
- Appliance City (UK). “How to Install a Tap.” Step-by-step guidance for pillar and bridge tap installations.
