Six mil plastic sheeting is 0.006 inches thick, equal to about 0.15 millimeters or roughly 150 microns — a medium-duty barrier ideal for vapor retarders and construction covers.
One mil equals 0.001 inch, so 6 mil is a thin, flexible sheet — not the heavy-duty material many assume. This thickness is the standard minimum for vapor barriers in most North American building codes, though the latest updates in some regions now require 10 mil for specific applications. Here is what 6 mil actually measures, where it works best, and the common mistakes that can get your project in trouble.
How Thick Is 6 Mil In Inches, Mm, And Microns?
The critical fact: 6 mil equals 0.15 mm — not 6 mm. A sheet sold as 6 mm would be forty times thicker and completely unusable for the same job.
| Unit | 6 Mil Equals | Reference Point |
|---|---|---|
| Inches | 0.006 in | 1 mil = 0.001 inch |
| Millimeters (mm) | 0.1524 mm (≈ 0.15 mm) | 1 mil = 0.0254 mm |
| Microns | ~150 microns | 1 micron = 0.001 mm |
What Is 6 Mil Plastic Sheeting Used For?
- Construction vapor retarders. It meets the minimum thickness for standard building codes in most regions — though some updated codes now specify 10 mil for crawl spaces or below-grade installation.
- Concrete curing covers. The sheet traps moisture for a proper cure without tearing under moderate weight.
- Temporary construction enclosures and erosion control. Light enough to drape and staple, strong enough for a single season outdoors.
- Drop cloths for painting and home maintenance. Better tear resistance than 2 mil or 3 mil painter’s plastic, yet still folds and stores easily.
- Agriculture and greenhouse covers. Silage covers and crop protection where light transmission matters and the plastic is replaced annually.
If you are planning a long-term underground vapor barrier or contain hazardous material, move up to 10 mil or thicker. Our roundup of 3 mil plastic sheeting covers the lighter-duty options for painting dust and short-term drop cloths.
How To Measure 6 Mil Plastic Sheeting Accurately
- Tool required: A digital or manual micrometer capable of reading to 0.001 inches.
- Procedure: Open the micrometer anvil, place the plastic sheet flat between the anvil and the spindle, and close gently until you feel light contact. Do not crank it tight; the plastic will compress and give a false reading.
- Reading: Lock the micrometer and read the display. A genuine 6 mil sheet reads 0.006 inches (or 0.15 mm). If the number reads 0.004 or 0.005, the material is thinner than labeled.
- Reinforced sheeting: If the plastic has an internal grid pattern (often called reinforced or woven polyethylene), measure at the cross-section of the grid — not on the flat surface between grid lines. The thickest point is where the reinforcement sits, and that is the true thickness for strength calculations.
Common Mistakes With 6 Mil Plastic Sheeting
- Mistaking mil for millimeter. A 6 mil sheet is 0.15 mm, not 6 mm. Buying “6 mm” plastic thinking it is “6 mil” lands you with material as thick as a smartphone — completely wrong for most jobs.
- Calling 6 mil “heavy-duty.” Compared to 2 mil painter’s drop cloths, 6 mil feels sturdy. But the real heavy-duty range starts at 10 mil. For floors that will see foot traffic, tools, or repeated dragging, skip 6 mil and go to 10 mil or 20 mil.
- Assuming all 6 mil is UV-resistant. Standard low-density polyethylene (LDPE) degrades within weeks in direct sunlight. Unless the packaging explicitly says “UV resistant,” treat clear 6 mil as an indoor or short-term outdoor material only.
References & Sources
- Global Plastic Sheeting. “Thickness of Plastic Sheeting: Mil Chart.” Defines 6 mil thickness and gives conversion to inches, mm, and microns.
- Global Plastic Sheeting. “Plastic Sheeting Mil Thickness Chart.” Lists common applications for each mil thickness.
- Global Plastic Sheeting. “Mil Thickness Compared to mm (Millimeters) and Inches.” Documents the correct unit conversion and common customer mistakes.
