Installing a bathtub overflow drain kit requires removing the old hardware, applying plumber’s putty to the new drain, securing the connections, and leak-testing with water above the overflow level.
For the full breakdown, see our best Bathtub Overflow Drain Kit guide.
Replacing a corroded overflow plate or installing a new drain assembly turns a messy plumbing job into a manageable weekend project. The key is getting each seal right before closing the access panel. This sequence works across standard waste-and-overflow kits and follows manufacturer guidance from brands like Oatey and Danco.
What Comes in a Bathtub Overflow Drain Kit?
A standard waste-and-overflow kit includes the drain strainer (brass or stainless steel flange), a waste shoe that threads onto the strainer from below, the overflow elbow and faceplate, gaskets for both openings, and a waste tee that ties the two branches into the home’s DWV line. Most kits also supply lock nuts, precut PVC tubing, and mounting screws.
If you’re shopping for reliable hardware, our roundup of the best bathtub overflow drain kits covers tested options for standard tub setups and common stopper types.
Step-by-Step Bathtub Drain Installation Sequence
The order below applies to most standard waste-and-overflow assemblies. You will work from above the tub and from the access panel below.
- Remove the old hardware. Unscrew the overflow faceplate and drain strainer from above. From below, disconnect the waste shoe and overflow elbow. If seized — common with mineral buildup — a reciprocating saw or dedicated drain wrench makes removal far easier than forcing it.
- Clean both openings thoroughly. Scrape away every trace of old putty, debris, and corrosion from the drain hole and overflow opening. A clean bonding surface is the most important condition for a leak-free seal.
- Apply sealant and seat the drain. Roll plumber’s putty into a thin rope and press it around the underside of the new drain strainer flange. Seat the strainer firmly in the drain opening, then wipe away any putty that squeezes out from above.
- Tighten the waste shoe from below. Hand-thread the waste shoe onto the strainer until the gasket compresses. Align the shoe’s outlet so it points directly toward the drain line.
- Install the overflow assembly. Fit the overflow gasket over the overflow opening from inside the tub. From the access side, insert the overflow elbow and hand-tighten the lock nut until the gasket compresses evenly. Rotate the faceplate so the overflow cutout faces downward —
- Dry-fit the waste and overflow piping. Measure, cut with a hacksaw or PVC cutter, then chamfer and deburr each cut end. Assemble all PVC pieces without cement to verify alignment is stress-free.
- Solvent-weld the joints. Apply PVC primer and cement per the kit instructions and local plumbing code. Work quickly, seat each connection firmly with a slight twist, and hold for a few seconds until the bond sets.
- Install the faceplate and stopper. Screw the overflow faceplate into place and add the drain stopper — toe-touch, trip-lever, or lift-and-turn — per your kit’s design. The stopper mechanism should move freely without binding.
- Leak-test the assembly before closing the access. Fill the tub with water until the level sits two inches above the overflow inlet. Wait five minutes and inspect every joint — drain connection, overflow elbow, waste tee — for any dripping. A dry test means the installation is complete.
Common Mistakes That Cause Leaks
Overtightening the drain nut or overflow lock nut distorts the gasket — every major kit manufacturer says to tighten by hand only until the gasket compresses, then stop. Skipping the dry-fit on the piping leaves the assembly under permanent stress, opening gaps over time as the PVC shifts. Failing to clean old putty from the drain opening prevents new sealant from bonding to the tub surface. The overflow faceplate cutout must face downward so overflow water enters freely. A fill test above the overflow level catches all of these issues before you close the access panel.
FAQs
Can I install a bathtub overflow drain kit without access from below?
Full installation requires reaching the drain shoe and waste tee from underneath the tub. If no access panel exists, you can cut one in an adjacent wall, closet, or the room below. Some partial repairs — like replacing just the overflow gasket — can be done through the overflow opening alone, but a complete kit replacement needs access from below.
What size drainpipe do I need for a standard overflow kit?
Most bathtub waste-and-overflow kits connect to a 1-1/2-inch drainpipe. If your existing pipe measures 2 inches, you will need a reducing bushing. Always confirm your drainpipe size and existing DWV configuration before ordering a kit.
How long does plumber’s putty last on a tub drain?
It stays slightly pliable — if it hardens and cracks, remove the strainer and reapply fresh putty or switch to silicone sealant, which offers a longer service life and remains flexible indefinitely.
Hand-tighten every connection, dry-fit every pipe section before cementing, and always fill the tub above the overflow to catch any hidden leak before considering the job finished.
References & Sources
- Oatey. “How to Install a Bathtub Drain.” Official installation steps for standard waste-and-overflow assemblies, including hand-tightening guidance and leak-testing procedure.
