How to Wire a 40 Amp Relay | Terminal-by-Terminal Guide

A 40 amp relay is wired by connecting power to terminal 30, the load to 87, a trigger to 86, and ground to 85, with an inline fuse on the feed.

Learning how to wire a 40 amp relay for automotive accessories like lights, fans, or fuel pumps is straightforward once you understand each terminal. The relay uses a small electrical signal from a switch to control a high-current circuit. Below is the terminal map, followed by a complete step-by-step sequence that applies to any 12V SPDT relay.

40 Amp Relay Terminal Functions

A standard 40 amp automotive relay uses standardized terminal numbers across virtually all brands.

Terminal Function Connection
30 Common / Power Input Battery positive (via fuse)
87 Normally Open Output Load (lights, fan, pump, etc.)
87a Normally Closed Output Load that runs when relay is off (5-pin only)
85 Coil Ground Ground (or trigger, depending on wiring)
86 Coil Positive / Trigger Switch or control signal

On a 4-pin relay, terminal 87a is absent. On a 5-pin relay, 87a is used only when the load must stay powered while the relay is idle; otherwise it is left unused. Terminal colors are not universal, so always verify the pin layout against the relay’s datasheet or socket markings.

Wiring a 40 Amp Relay Step by Step

These steps apply to any 12V automotive relay. Always disconnect the battery negative terminal before starting.

  1. Disconnect the battery negative terminal — prevents accidental shorts.
  2. Identify your relay terminals — numbers are molded into the relay base. RS Components’ relay wiring guide provides a detailed terminal-function breakdown. Confirm whether you have a 4-pin or 5-pin relay.
  3. Run fused battery power to terminal 30 — crimp a ring terminal on a wire from the battery positive, place an inline fuse as close to the battery as possible (40A or appropriate rating for your load), then connect that wire to terminal 30.
  4. Connect the load to terminal 87 — run a wire from terminal 87 to the positive side of your accessory. Ground the load’s negative side separately to clean chassis metal.
  5. Wire the trigger circuit — connect your switch or control signal to terminal 86, and connect terminal 85 to a clean chassis ground. The coil is not polarity-sensitive, so 85 and 86 can be reversed.
  6. For 5-pin relays only — if you need the load powered when the relay is off, connect it to terminal 87a instead of 87. Otherwise leave 87a unconnected.
  7. Crimp and insulate every connection — use properly sized crimp terminals, a crimping tool, and heat shrink tubing or electrical tape over each joint.
  8. Secure the relay — mount it in a dry location using the mounting tab, or plug it into a secured relay socket.
  9. Test before finalizing — reconnect the battery negative, activate the trigger, and confirm the load turns on and off. If not, check that terminal 30 has power, the load is grounded, and the coil is receiving voltage.

For help choosing the right component, our roundup of the best 40 amp relays covers tested options for different applications.

What Are the Common Wiring Mistakes to Avoid?

Most relay wiring failures come from repeated errors:

  • Mixing up terminal numbers — swapping 30 and 87, or reversing 85 and 86, is easy under the dash. Double-check every wire before crimping.
  • Omitting the fuse — an inline fuse on the power feed to terminal 30 is not optional. A short without a fuse can melt wiring or start a fire.
  • Poor grounding — terminal 85 or 86 must connect to clean, bare metal on the chassis or battery negative. Paint, rust, or a loose screw creates an intermittent circuit.
  • Using the wrong terminal for the load — on a 5-pin relay, connecting the load to 87a instead of 87 means it runs when the relay is off, which is almost never what you want.
  • Forgetting to disconnect the battery — working on a live 12V circuit risks sparks, shorts, and accidental engagement.
  • Loose or poorly crimped connections — a crimp made with pliers instead of a proper crimping tool loosens over time, creating resistance and heat.

The relay rating only describes its own contact capability — the wiring, fuse, socket, and switch must all be rated for the current you draw. A 40A relay on undersized wire is still a fire hazard.

FAQs

Can I use a 40 amp relay for LED lights?

Absolutely. A 40 amp relay works perfectly for LED light bars and similar accessories because LEDs draw far less current than the relay’s rating. The relay runs cool and reliable with that much headroom, and the 40A contact rating means it will never be stressed by an LED load.

What wire size do I need for a 40 amp circuit?

This keeps voltage drop below acceptable limits and prevents the wire from heating under full load. The ground and load wires should also match this gauge to avoid a bottleneck.

Does a relay need a fuse on both the power and trigger sides?

Only the main power feed to terminal 30 needs an inline fuse. The trigger circuit on terminal 86 draws negligible current — just milliamps — so it does not need a separate fuse. If the trigger wire passes through a switch with a built-in fuse, you can leave that in place for extra protection.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.