How to Make Jewelry From Coins | Turn Pocket Change Into Wearable Art

Turning coins into jewelry is possible with basic tools: drill a hole, smooth the edges, and attach findings like jump rings or earring hooks to create pendants, rings, or earrings.

The polished coin pendant you saw on Etsy started as ordinary pocket change. You can make coin jewelry at home with a $20 drill, basic jewelry pliers, sandpaper, and about an hour of careful work. Silver and copper coins work best for shaping; steel coins are too hard without industrial tools. For ready-made pieces, the best ancient coin jewelry collection includes museum-quality options that skip the DIY effort.

What Coins Work Best For Jewelry Making?

Metal composition determines if you can drill, shape, and polish a coin at home. Silver and copper are prime candidates because they soften under heat and respond to filing and polishing. Steel coins are too hard for home tools, and aluminum can melt during the heating required for rings.

Test your coin with a magnet: magnetic coins are almost certainly steel and will frustrate every attempt to drill or shape them. Non-magnetic coins, especially older silver or copper ones, are what you want. Check the coin’s date and mint information online to confirm its composition.

Making A Coin Pendant: The Basic Method

Drilling a clean hole and attaching a jump ring turns almost any coin into a wearable pendant. This is the simplest project for beginners.

  1. Clean the coin with warm soapy water and a soft brush, then dry thoroughly. Oils and dirt prevent polish bonding and can cause the drill bit to slip.
  2. Mark the drill point with a fine-point marker or center punch. A small indentation stops the bit from wandering.
  3. Secure the coin on scrap wood or in a table vice. The backing protects your work surface and keeps the coin from spinning.
  4. Drill a pilot hole with a 1/16-inch or 1 mm bit. Go slowly — too much pressure snaps small bits. Drilling all the way through works fine for a pendant hole.
  5. Smooth the edges with a file, fine sandpaper, or a rotary tool. Sharp burrs snag clothing or scratch skin.
  6. Attach jewelry findings: open a jump ring with pliers, thread it through the hole, and close securely. For a cleaner look, place the coin in a bezel pendant setting before attaching the chain.
  7. Polish with a jewelry polishing cloth until the surface shines.

Go slowly through every step. Rushing the drill hole is the most common mistake — a snapped bit or wandering hole ruins the coin.

How Do You Make A Coin Ring?

Coin rings require more tools and patience than pendants but produce striking results. The process centers on annealing — heating the metal to soften it so you can shape it without cracking.

Start by punching or drilling a center hole sized to the wearer’s finger — roughly 10–12 mm for an average adult ring. Heat the coin to a dull red using a torch, then quench in water to soften the metal. Drive the coin over a ring mandrel or shaping tool, repeating the annealing step as the metal stiffens. File and sand the exterior and interior until smooth, then polish to a mirror finish.

Interweave’s jewelry crafts guide notes that silver and copper respond best to repeated annealing, while steel coins resist shaping at every stage. Expect to invest an afternoon for a quality result.

Three Mistakes That Ruin Coin Jewelry

  • Skipping the cleaning step. Oils and dirt prevent proper bonding during polishing and cause the drill bit to slip, scratching the coin’s surface.
  • Drilling without a center punch. A smooth coin face gives the bit nothing to bite into — it wanders immediately, leaving an off-center hole that cannot be fixed.
  • Choosing the wrong coin metal. A steel coin that tests magnetic resists drilling, refuses to anneal, and will likely break your drill bit. Start with silver or copper.

Coin jewelry rewards patience over speed. A single silver quarter can become a pendant, ring, or earring that outlasts factory-made jewelry — but only if you let the metal dictate the pace.

FAQs

Is it legal to make jewelry from coins?

In the US, altering circulating coins for jewelry is a gray area. The law prohibits melting pennies and nickels for their metal value, but crafting coins into jewelry for personal use or as art is generally tolerated. Consult a legal source for definitive guidance.

What is the easiest coin jewelry project for beginners?

A drilled coin pendant is the simplest project — it requires only a hand drill, a 1/16-inch bit, sandpaper, a jump ring, and pliers. No heating or metal shaping is needed, and a beginner can complete one in under an hour.

Can I use a steel coin for jewelry?

Steel coins are difficult to work with at home. They resist drilling, cannot be annealed with a standard torch, and often break drill bits. Some steel coins can be used as pendants if drilled carefully, but ring-making is impractical without industrial tools.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.