AllerEase mattress protectors are machine washable, but the temperature depends on your specific model — check the sewn care label for warm or hot wash and always dry on low heat.
An AllerEase protector keeps allergens, dust mites, and spills out of your mattress, but washing it wrong can damage the waterproof membrane. The single smartest cleaning rule across every official instruction: check the sewn label on your exact model. Some AllerEase protectors call for warm water; others say hot up to 120°F. The drying rule never changes — low heat only, remove promptly, and never reach for the iron. If you’re replacing an old protector or shopping for a new one, our tested roundup of the best anti-allergy mattress protectors covers top picks for every bed depth and budget.
Which Wash Temperature Does Your AllerEase Model Need?
The answer is genuinely model-dependent, so the sewn-in care label is your primary source. The three most common AllerEase models follow patterns below:
| AllerEase Model | Wash Temperature | Dry Setting |
|---|---|---|
| Waterproof Allergy Protection (polyester/polyethylene) | Machine wash warm | Tumble dry delicate / low heat |
| Maximum Waterproof (up to 120°F rated) | Machine wash hot | Tumble dry low heat |
| Platinum Twin XL Zip-Off Plush Top (fits 14″ mattresses) | Machine wash hot, wash separately | Lowest dryer setting, separately |
| Waterproof Protector (American Textile shop listing) | Machine wash hot | Tumble dry low heat |
Washing Steps That Protect the Membrane
Follow these steps to keep the protector effective through many cycles. The two minutes it takes to read this can add years to its life.
- Unzip and remove the protector from the mattress. This prevents stress on the zipper and lets the fabric wash evenly.
- Read the sewn care label for the exact temperature instruction. The label is your authoritative source — product pages vary, but the tag sewn into the hem is model-specific.
- Machine wash with regular laundry detergent. Use non-chlorine bleach only if the care label permits it; many AllerEase models list “only non-chlorine bleach when needed” or prohibit chlorine bleach entirely.
- Dry on low heat — the lowest setting your dryer offers. AllerEase’s official guidance notes that gas dryers heat up faster and run hotter than electric dryers; if you use gas, run the dryer in 10-minute low-heat increments until the protector is dry.
- Remove promptly when dry. Letting it sit in the drum hot can weaken the waterproof backing.
- Do not iron. The heat will damage the polyethylene or polyurethane barrier layer. Do not dry clean either — chemical solvents can break down the waterproof membrane.
- Reinstall only when the protector is completely dry. Putting a damp cover over the mattress invites mildew growth.
Common Mistakes That Shorten the Protector’s Life
Using the wrong wash temperature is the most frequent error — some protectors are labeled warm, others hot, and picking the wrong one either fails to clean adequately (too cool) or stresses the fabric weave (too hot on a warm-rated model). Chlorine bleach is explicitly forbidden or limited to non-chlorine only across every AllerEase instruction. High heat in the dryer is the fastest way to delaminate the waterproof layer; always set the dial to low heat or the lowest delicate setting. Ironing or dry-cleaning are also definite no-gos. Official recommendations from American Textile, which makes AllerEase protectors, advise washing every two months to keep allergen protection effective.
FAQs
Can I use fabric softener on an AllerEase mattress protector?
Fabric softener is not recommended. It coats the fibers and can reduce the waterproof barrier’s effectiveness over time, especially on the polyethylene-backed models. Stick to regular liquid or powder laundry detergent.
How often should I wash an AllerEase mattress protector?
Every two months is the standard official recommendation. This schedule maintains allergen protection and keeps the fabric fresh. If you have active allergies or pets, every four to six weeks is reasonable.
What happens if I accidentally dry it on high heat?
High heat can melt or delaminate the waterproof polyurethane or polyethylene membrane, causing the protector to leak. If high heat was used once and the protector still looks intact, it’s likely still fine. Repeated exposure will eventually damage the barrier.
References & Sources
- AllerEase. “Mattress and Pillow Protectors.” Official product hub with care instruction references.
- American Textile. “Care Information.” General AllerEase care guidelines, including wash temperature and gas-dryer advice.
- American Textile. “AllerEase Waterproof Protector.” Product-page care instructions confirming hot wash and low-heat dry.
