A properly adjusted office chair supports your lower back, keeps your feet flat, and aligns your elbows near 90 degrees — preventing strain from the first hour through the eighth.
Most people sit in a chair that was never tuned to their body. The seat’s too high, the lumbar pad misses the curve, or the armrests push the shoulders up. The fix takes about two minutes and changes how the whole workday feels. Here is the exact order to adjust every control on your chair, with the measurements that actually matter.
Seat Height – Where the Whole Setup Starts
Stand beside the chair and raise the seat until its highest point sits just below your kneecap. When you sit down, your feet should rest flat on the floor with your thighs roughly parallel to the floor. UNC Environmental Health and Safety calls this the starting point and recommends making small tweaks after sitting for a while. If your feet do not reach the floor flat after this adjustment, use a footrest rather than lowering the chair — a footrest keeps the thigh angle correct.
Seat Depth and Thigh Clearance
While seated, check the gap between the front edge of the seat and the back of your calf. You want about a clenched-fist width — roughly 2 inches or 5 centimeters. The Canadian Centre for Occupational Health and Safety (CCOHS) uses the same fist-width rule. If the seat is too deep and presses behind your knees, adjust the seat depth slider forward. If your chair lacks a depth slider, add lumbar support to push your pelvis back rather than letting the seat edge dig in.
Backrest, Lumbar Support, and Tilt
The backrest should fit into the natural curve of your lower back — the inward hollow just above your hips. Slide the backrest up or down until the lumbar pad sits in that spot. UCLA Health Safety advises setting the upper body at a slight recline around 110 degrees rather than locking the chair bolt upright. A slight recline lets your spine move naturally and reduces pressure on the discs. Never lock the backrest in a rigid position; the resistance should support movement, not fight it.
If you need a new chair to get this right, our roundup of the best adjustable office chairs covers models with proper lumbar depth and tilt range.
Armrests – Light Touch, No Lift
Set each armrest so your elbows bend at roughly 90 degrees and your forearm rests on the pad without raising your shoulders. The armrest should barely touch the underside of the elbow. CCOHS explicitly says to remove the armrests if their lowest setting still forces your elbows upward — raising your shoulders for hours creates neck and trap strain that a chair should prevent.
| Adjustment | Target Position | Common Mistake |
|---|---|---|
| Seat height | Seat just below kneecap; feet flat | Chair too high, feet dangling |
| Seat depth | 2-inch gap between seat edge and calf | Seat edge pressing behind knees |
| Lumbar support | Fits the lower back’s natural curve | Lumbar pad too high or missing |
| Backrest tilt | Slight recline around 110 degrees | Locked rigidly upright |
| Armrests | Elbows at 90°, shoulders relaxed | Too high, lifting the shoulders |
After adjusting, check your workstation match: your forearms should be parallel to the desktop when typing, and your wrists straight. If the desk height is fixed and forces your elbows below 90 degrees, raise the chair and add a footrest rather than slouching. A well-tuned chair and desk together keep the whole upper body neutral through the workday.
FAQs
Should I lock the chair tilt or leave it free?
Leave the tilt unlocked with moderate resistance. A slight recline around 110 degrees supports natural spine movement and reduces disk pressure. Locking the chair rigidly encourages static posture and increases fatigue over time.
How do I know if the seat depth is wrong?
If the front edge of the seat presses into the back of your knees or calves, the depth is too large. You should be able to fit two to three fingers — or a clenched fist — between the seat edge and your calf without contact.
Can I use an office chair without armrests?
Yes. If the armrests in their lowest position still raise your shoulders or prevent the chair from sliding under the desk, remove them. Your elbows should rest naturally at 90 degrees without being pushed up.
References & Sources
- Canadian Centre for Occupational Health and Safety. “Office Ergonomics – Adjusting Your Chair.” Provides the fist-width calf clearance and armrest height rules.
- UNC Environmental Health and Safety. “Office Ergonomics.” Recommends starting with seat height and making small adjustments after sitting.
- UCLA Health Safety. “Chair Setup.” Advises 110-degree recline and lumbar support matching the lower back curve.
