“`html
Aircraft cable is small-diameter wire rope made from twisted steel strands, used in flight controls, rigging, railings, and winch lines.
Understanding what aircraft cable is starts with its name: it’s a compact wire rope, almost always 3/8 inch or smaller, built from strands of steel wire wound into a strong yet flexible cable. The name dates back to early aircraft control systems, and it still appears on cable made for airplanes. Today the same term is used just as often for industrial, marine, architectural, and rigging cable that never leaves the ground.
The build is the same at every size. Individual wires are twisted into strands, and strands are then twisted into the finished cable. The two dominant constructions are 7×7 and 7×19. Most aircraft cable is galvanized steel or stainless steel, with 304 and T316 stainless among the common corrosion-resistant variants.
What Sets Aircraft Cable Apart From Wire Rope?
Aircraft cable is wire rope, and at small diameters the two names are often used interchangeably. The usual dividing line is size: aircraft cable is generally recognized from 1/32 inch up to 3/8 inch, while larger-diameter rope is classified separately as wire rope.
The construction numbers describe how the cable is built. A 7×7 cable has seven strands with seven wires each, which gives it a firmer feel and less flexibility. A 7×19 cable also uses seven strands, but each strand contains nineteen wires, which makes it noticeably more flexible and smoother running over pulleys, sheaves, and winch drums. That flexibility is why 7×19 shows up so often where cable has to bend repeatedly.
Material choice is mostly about corrosion. Galvanized steel carries a protective zinc coating and covers most indoor and general outdoor jobs at a lower cost. Stainless steel, especially T316, is the better pick for saltwater, marine rigging, and anything that will spend years outdoors.
How Strong Is Aircraft Cable? Sizes And Ratings
Strength depends on diameter, construction, and material, and the working load limit is always lower than the breaking strength. The table below lists typical published ratings for 7×19 stainless steel aircraft cable.
| Nominal Diameter | Breaking Strength | Working Load Limit |
|---|---|---|
| 1/16 in. | 480 lb | 96 lb |
| 3/32 in. | 920 lb | 184 lb |
| 1/8 in. | 1,760 lb | 352 lb |
| 5/32 in. | 2,400 lb | 480 lb |
| 3/16 in. | 3,700 lb | 740 lb |
| 1/4 in. | 6,400 lb | 1,280 lb |
| 5/16 in. | 9,000 lb | 1,800 lb |
| 3/8 in. | 12,000 lb | 2,400 lb |
These are representative numbers, not a guarantee for a specific coil. Suppliers rate the same diameter differently depending on construction and material; a 1/4 inch galvanized 7×19 cable, for example, is commonly listed at 7,000 lb breaking strength and 1,400 lb working load limit. In the table above, the working load limit runs about one-fifth of the breaking strength, and that gap is part of your safety margin. Always plan around the working load limit, add a safety factor for shock loads, and check the manufacturer’s data sheet before rigging anything.
Uses, Limits, And The Aviation-Grade Distinction
Aircraft cable is used wherever a strong, flexible small-diameter cable is needed, but the aviation name does not automatically mean aviation-approved. On smaller airplanes, control cables are wire rope, and EAA’s control-cable article explains how they connect cockpit controls to the primary flight controls.
Outside the hangar, the same style of cable is standard in winch lines, slings, fences, railings, sailboat rigging, suspension lines, and general rigging. Commercial-grade galvanized or stainless aircraft cable is a proven choice for those jobs.
The distinction matters when the cable is headed for an airplane. Critical aerospace use calls for cable built to a military specification such as MIL-DTL-83420. Commercial references also cite RR-W-410 and ASTM A1023, with RR-W-410 Type VI class 2 covering 7×7 and class 3 covering 7×19. Do not assume a product labeled “aircraft cable” meets flight standards just because the label says so; buy cable sold explicitly for aviation use and pair it with the correct hardware, routing, and installation.
Once you know the ratings that matter, comparing options is straightforward, and our roundup of the best aircraft cable covers the sizes and constructions worth buying.
Keep three numbers straight when you buy: size, construction, and working load limit. Match the flexibility of 7×7 or 7×19 to the job, pick galvanized or stainless for the environment, use the working load limit rather than the break strength, and trust only MIL-spec cable in a plane.
FAQs
Is every “aircraft cable” safe for use in airplanes?
No. The label is used broadly for general-purpose wire rope, and only cable meeting an aerospace specification such as MIL-DTL-83420 should be trusted in critical flight-control systems. For non-aviation work, standard galvanized or stainless steel aircraft cable is fine, but verify the product’s ratings against its spec sheet before relying on it.
What does 7×19 mean?
The first number is the number of strands, and the second is the number of wires in each strand. A 7×7 cable has seven strands with seven wires each, while a 7×19 cable has seven strands with nineteen wires each. More wires per strand makes 7×19 more flexible, which is why it is common in running rigging and winch lines.
What’s the difference between breaking strength and working load limit?
Breaking strength is the load at which the cable is expected to fail, while working load limit is the maximum load you should apply in normal use. The two are not interchangeable; working load
