How to Choose a Tankless Water Heater? | Size Is The Game

Sizing a tankless heater means matching its flow rate in GPM to your home’s peak hot-water demand at the required temperature rise.

Every tankless water heater is a flow-rate promise, and the real question behind how to choose a tankless water heater is whether that promise holds when your household uses the most hot water at once. Showers back to back, the dishwasher running, the washing machine filling — that is the moment a too-small unit fails and a right-sized one goes unnoticed. The decision narrows to two numbers: peak hot-water flow in gallons per minute (GPM) and temperature rise. Nail those, and fuel type, efficiency, and venting all fall into place around them.

How Do You Size A Tankless Water Heater?

You size a tankless heater by adding the flow rate of every hot-water fixture that could run at the same time, then comparing that total to the unit’s rated GPM at the temperature rise your home needs. A heater that clears both numbers belongs in the running; one that clears only the sticker GPM does not.

This Old House’s buying guide spells out the sequence:

  1. List the fixtures that might run together at peak — usually the morning rush or the evening shower block.
  2. Write each fixture’s flow rate in GPM, from its spec sheet or a typical value.
  3. Add them for your maximum simultaneous flow.
  4. Estimate incoming cold-water temperature, subtract it from your desired output — most guides target 120°F — and the difference is your temperature rise.
  5. Compare both numbers against the heater’s published flow ratings, which are always stated at a specific temperature rise.

Consumer Reports offers a useful demand-side shortcut: a two-person household often fits a 6–8 GPM unit, while a family of four typically needs 8–10 GPM. Those ranges assume a moderate climate, so use them as a starting point, not a substitute for the math. Heater ratings only mean something when they name the temperature rise they were measured at — always compare at your rise, not at the manufacturer’s most flattering number. The most common sizing failure is underestimating simultaneity: two people showering back to back is easy for any unit, but two showers at once changes the math completely. Typical fixture rates in the table below come from This Old House and standard U.S. fixture specs.

Fixture Typical Flow Rate (GPM)
Kitchen faucet 1.5–2.2
Bathroom faucet 1.0–2.0
Showerhead 1.25–2.5
Dishwasher 1.0–2.5
Tub filler faucet 4.0
Washing machine 1.5–3.0

What Else Matters Beyond The GPM Rating

Sizing builds the shortlist; these four filters shrink it to the unit that will actually work in your home.

  • Gas versus electric. Gas tankless units need venting to the outside and often a larger gas line, and their capacity is rated in BTUs. Electric units draw heavy current and may require an electrical panel upgrade. Check what the home can physically support before you get attached to a model.
  • Condensing versus non-condensing. Condensing models recover extra heat from exhaust, which boosts their UEF efficiency rating and allows smaller PVC venting, at a higher purchase price. Non-condensing units cost less, run less efficiently, and usually need metal venting.
  • Climate. Colder incoming water means a bigger temperature rise, and a bigger rise cuts delivered flow. The same heater that handles two showers in Georgia may barely manage one in Minnesota. Regional groundwater temperature maps give a solid estimate if you don’t want to measure it yourself.
  • Installation and maintenance. Whole-home gas installs are skilled work — confirm a qualified installer exists for the unit you want before you buy. Upkeep matters too: buying guides note that maintenance requirements carry warranty and service implications, so check the descaling routine up front.

Put It Together: A Worked Example

Here is the method applied end to end. Take a two-bathroom house where incoming groundwater sits near 50°F in winter; with a 120°F shower target, that is a 70°F temperature rise. The worst morning is two showers at 2 GPM each plus a bathroom faucet at 1.5 GPM — 5.5 GPM total. A heater rated 5.5 GPM at a 70°F rise just covers it; one rated 5.5 GPM at a 45°F rise does not. Add a second faucet to that morning and the peak jumps to 7 GPM, which pushes the choice up a size class.

Manufacturers publish flow curves, not a single GPM number, because rated output drops as temperature rise climbs. Match the curve, not the sticker, and size for the worst month of the year rather than the average.

Once your numbers are locked, the shortlist builds itself. Compare actual units side by side in the 10 best tankless water heaters we’ve tested, ranked by flow rate, efficiency, and ease of installation.

The whole method reduces to one pass: worst month, worst morning, fixtures summed, rise computed, curve matched. Do that once, and the brand and budget conversation takes care of itself.

FAQs

What size tankless water heater does a family of four need?

Consumer Reports finds a four-person household usually needs a unit rated for 8–10 GPM, while two residents often fit a 6–8 GPM heater. Those figures assume typical groundwater temperatures, so run the rise math for your region first — cold-climate homes may need more capacity than the shorthand suggests.

Why does incoming water temperature matter so much?

A tankless rating only holds at a specific temperature rise. Groundwater at 50°F in winter plus a 120°F target equals a 70°F rise, while a warmer region may need only 45°F. The same unit delivers less hot water at the bigger rise, which is why northern homes often buy a size up.

Can I install a tankless water heater myself?

Small electric point-of-use units are a realistic DIY project. Whole-home gas units are another story: venting, gas-line sizing, and often electrical work push most installations toward a licensed professional. Checking installer availability before purchase is one of the most repeated pieces of buying guidance.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.