How to Paint Toy Soldiers | From Sprue to Showpiece

Painting toy soldiers is a five-step process: clean, prime, base coat, detail, and seal, with a plastic-bonding primer being essential for durable results.

Painting toy soldiers transforms cheap plastic figures into display-worthy pieces, but the difference between a paint job that lasts and one that flakes off comes down to preparation. Whether you’re working on green army men, 15mm infantry, or larger soft-plastic figures, the core workflow is the same. The payoff is a set of soldiers with sharp detail and a finish that survives handling.

The Right Way to Prep Plastic Figures

Surface preparation decides how long your paint job survives. Most plastic figures come straight from a mold with a residue called a release agent that prevents paint from bonding. Skipping this step is the single most common reason paint chips off later.

Wash the figures in warm water with a drop of dish soap — the research sources specifically name Dawn — and scrub them with an old toothbrush. Rinse thoroughly and let them dry completely; one guide recommends overnight. While they dry, trim away flash, seam lines, and mold lines with a sharp craft knife and a fine file or emery board. A clean surface is the foundation everything else sits on.

Priming Is Non-Negotiable for Plastic

Plastic is slick, and regular paint alone will not hold to it well. Multiple guides warn that skipping primer, or using paint that doesn’t bond to plastic, leads to chipping and flaking. The fix is a spray primer or spray paint specifically labeled for plastic — Krylon and Rust-Oleum plastic spray paints are both named in the research as suitable options. Check the can: it should say it bonds to plastic.

Apply the primer in thin, even coats rather than one thick blast. Heavy primer buries fine detail, which is especially a risk on soft plastic figures. Two light passes from about eight inches away give better coverage than one wet coat.

Base Coats, Details, and the 3–5 Color Rule

Acrylic paints are the standard choice for miniature painting because they layer well and dry fast. Start with the dominant uniform color, then work down to smaller details like faces, straps, boots, and weapons. A common order is to paint the skin and inner areas first, then the outer gear, so you can reach everything without overpaint.

One strong piece of advice from the sources: limit your palette. . Overloading a small figure with too many colors destroys readability — up close it looks busy, and at arm’s length it reads as noise. Keep three brush sizes on hand (large, small, and fine) for base coating, detail work, and thin edge highlights.

Sealing the Finish

A protective clear coat is the final step that keeps your work intact. Options include clear matte enamel, polyurethane gloss, matte spray, or a dulling agent, depending on the sheen you want. Matte finishes look most natural for military figures; gloss adds durability but a shiny surface.

Spray sealers demand a well-ventilated area, since aerosol fumes are strong. Liquitex Gloss is one named clear-coat option, and Vallejo gray primer is a cited choice for the priming step. If you prefer brush-on varnish, it’s easier to control and less dependent on ventilation. Apply one or two thin coats and let the figures cure fully before handling them. Once your first squad is done, you may want to build out a full army — our roundup of the best army soldier toys covers the figures worth painting.

Step What To Use Common Mistake
Wash Dish soap, old toothbrush Skipping this leaves release agent that repels paint
Cleanup Craft knife, fine file Leaving mold lines that show through paint
Prime Plastic-bonding spray (Krylon, Rust-Oleum) Thick coats that bury detail
Base coat Acrylic paint, large brush Starting with tiny details before the main color
Detail Small/fine brushes, 3–5 colors Too many colors killing readability
Seal Matte or gloss clear coat Painting before figures are fully dry

For deeper technique on shading, highlighting, and brush care, the Wargamer’s painting miniatures guide is a solid next stop. Warfare History Network and BoardGameGeek’s miniature painting wiki also offer solid step-by-step coverage of the same core workflow.

FAQs

Do I need to prime plastic toy soldiers?

Yes. Plastic is smooth and slick, so standard paint won’t bond to it and will chip off over time. A spray primer labeled for plastic creates the grip your paint needs. Apply it in thin, even coats so you don’t obscure the figure’s detail, and let it dry fully before base coating.

What kind of paint works best on toy soldiers?

Acrylic hobby paints are the standard choice. They dry quickly, layer well, and clean up with water, which makes them forgiving for beginners. Enamel paints are more durable but slower-drying and require thinner for cleanup, so most miniature painters stick with acrylics for the base work.

How long should I wait between coats?

When in doubt, wait longer; rushing the drying time is a common cause of smudged paint.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.