Hang string lights by installing a tensioned support wire between anchors, then clipping the strand to it every 12–18 inches.
Most people hang string lights by draping the strand directly from post to post, and most regret it within a season. The cord sags, the sockets stress, and wind turns a neat run into a tangled droop. Whether lighting a deck, patio, or backyard, hanging string lights the right way starts with measuring the span and ends with testing every bulb. The single biggest upgrade most setups need is a support wire that carries the weight so the light cord doesn’t have to.
Plan The Layout Before You Touch A Ladder
Start by measuring the distance between the two structures you’re spanning, then choose your pattern — straight line, zig-zag, or perimeter. Mark each anchor point and confirm you can reach an outlet or extension-cord route before installing anything; discovering the strand can’t reach power after everything is hung is the most avoidable mistake.
For outdoor runs, find sturdy attachment points at least 9 feet off the ground. Pre-drill guide holes in soffits, deck posts, and mature tree trunks so screws and eye bolts seat cleanly without splitting the wood. Home hardware retailers recommend drilling starter holes, then threading eye bolts in by hand.
The Support Wire Method That Keeps Lights Taut
The guy wire takes the tension, so the light strand never bears the full load. Hang the support wire first, before the lights go up.
Even on shorter spans, a support wire makes the difference between a sagging mess and a clean line. That slight sag is intentional — it keeps sockets from stressing against the tension.
Keep cords clear of walkways, and remove the bulbs before hanging to reduce breakage.
Fasteners: Hooks, Eye Bolts, And The Staple Risk
Choose anchors based on the surface. Soffits and wooden posts take screw-in eye bolts; brick or concrete need masonry hooks; trees take eye bolts driven into pre-drilled holes. Thread the support wire between eye bolts and twist it tight with pliers, then slide each bulb attachment into place.
If fastening to a railing, secure the wire or cord underneath with staples aimed so they can’t touch the insulation, or skip staples entirely and use zip ties around the railing itself.
For indoor ceiling borders, self-adhesive hooks spaced about 2 feet apart handle the job fine. Position the plug end near an outlet, then loop the strand over each hook.
| Setup Decision | What To Use | Key Detail |
|---|---|---|
| Long spans (100+ ft) | 1/8″ galvanized cable + eye bolts | Attach bulbs with 4-inch wire pieces |
| Short outdoor spans | Support wire + zip ties or carabiner clips | Space clips every 12–18 inches |
| Ceiling borders indoors | Self-adhesive hooks | Space hooks about 2 feet apart |
| Railings | Zip ties or staple underneath | Never let staples puncture the cord |
Connect, Test, And Avoid The Common Mistakes
Hang the first strand with the male plug closest to the outlet, then connect additional strands end-to-end or via an extension cord as needed. Check the manufacturer’s maximum connectable strand count before linking multiples — exceeding it is a safety limit, not a suggestion. Keep plugs and connections elevated and protected from weather, and use a GFCI-protected outlet for any outdoor wet-location work. Turn off power before installation, test the full run before finalizing, and use a helper for alignment.
The mistakes that ruin most installations: hanging long spans with no support wire, over-tightening so there’s zero slack, skipping the pre-test, and running cords across walkways. Each is easy to avoid when you plan first. If a battery-powered setup makes more sense than running extension cords, our roundup of the best battery pack string lights covers tested models that skip the outlet problem entirely.
Once everything connects and every bulb glows, give the line a final sag check — then enjoy the only part of the job that matters.
FAQs
What height should outdoor string lights hang at?
Hang the strand 8–10 feet above the ground, which keeps the lights clear of head-height traffic and still low enough to light the space well. On long runs, allow for a natural droop of about 6 inches per 10 feet so socket connections don’t bear unnecessary tension.
Can I hang string lights directly between trees without extra wire?
You can for short, low-tension runs, but on spans approaching 100 feet or more, a support wire is strongly recommended. The light cord alone will sag and stress its sockets over time. Running a separate cable between the trees and attaching the strand to it keeps the light cord healthy.
Is it safe to use indoor string lights outdoors?
No. Indoor lights aren’t built to handle moisture, temperature swings, or UV exposure, and using them outdoors creates a shock and fire hazard. Outdoor-rated or wet-location string lights use sealed sockets and weather-resistant insulation designed for the conditions.
References & Sources
- Lowe’s. “How to Hang Backyard String Lights.” Details on 1/8-inch cable, 4-inch wire attachments, and eye bolt installation.
- Home Depot. “How to Hang Outdoor String Lights.” Provides the measure, drill, install, and test sequence for outdoor runs.
- The New York Times (Wirecutter). “How to Hang Outdoor String Lights.” Explains the support-wire method and spacing guidelines for clean, stable installs.
