Buying a 90×90 curtain is simple until you hang it and find it’s six inches short or too skimpy to cover the glass. The size refers to the finished panel dimensions, but the measurements that matter are your track width, your drop, and the fullness you want. Getting all three right means measuring the installed pole, deciding where the hem should land, and choosing a heading that gives the gathered look you expect.
What Does 90×90 Mean Exactly?
A 90×90 curtain is a standard size: 90 inches wide by 90 inches long. UK and Irish retail guides list this same size as roughly 228 × 228 cm. The width refers to each panel’s finished width, and the drop is measured from the top of the heading to the bottom hem.
One honest caveat: some stores round the metric equivalent differently, so use the exact size shown on the product page rather than assuming a conversion. If a product lists 228 cm, that’s the number to work with, not a rounded figure from memory.
How Do You Measure the Width?
Measure the full width of the pole or track, excluding the decorative ends and finials. This is the single most common mistake — people measure the window glass and end up with curtains that don’t cover the walls on either side. The track or pole is the anchor point, not the window frame.
For a gathered look, the fullness you need depends on your heading type:
- Pencil pleat: roughly the width of the track or pole
- Tab top: about 1.5× the track width
- Eyelet: about 2× the track width
Heavier materials need less fullness; sheer fabrics need more. If you’re buying a pair, divide the total width between the two panels and add a small overlap allowance so they meet in the middle without a gap.
How Do You Measure the Drop?
The drop depends on your heading type and where you want the hem to land. For eyelet curtains, measure from the top of the pole to your endpoint, since the curtain hangs from the pole itself. For pencil pleat or pleated curtains, measure from the top of the track or from the bottom of the rings or hooks, depending on the heading.
Decide the style first, because the endpoint changes everything:
- Sill length: hem sits just below the window sill
- Below sill: hangs a few inches below the sill
- Floor length: measure from the pole top to the floor and subtract about 1 cm for clearance
- Puddle style: fabric pools on the floor, so add extra length
If a radiator sits below the window, keep the hem about 3 cm (1½ inches) above the radiator top so heat can flow freely — curtains that trap heat behind them can reduce heating efficiency and risk fabric damage over time.
For eyelet curtains specifically, remember the heading adds a stand-up above the pole, so make sure there’s room for it. That stand-up is roughly 5 cm above the pole, which matters if you have a high ceiling or a close-fitting valance.
Where Should the Pole Go?
If you haven’t installed the pole yet, all your length decisions should be based on where the rod will sit, not on the current window trim. The pole should extend beyond the window on both sides so the curtains can stack back and let light in when open.
The pole height also affects the perceived ceiling height — hanging it closer to the ceiling than to the window top makes the room feel taller. Just keep it high enough that the curtain heading clears the window frame completely when drawn.
| Heading Type | Measure Drop From | Fullness Factor |
|---|---|---|
| Eyelet | Top of the pole | 2× track width |
| Pencil pleat | Top of track or hook | 1× track width |
| Tab top | Top of the pole | 1.5× track width |
If you’re ready to see what’s available, our tested roundup of the best 90×90 curtains narrows down the options that actually fit standard windows.
Home Depot’s curtain measuring guide walks through the same steps with helpful diagrams if you want a visual reference.
FAQs
What if my window is wider than 90 inches?
A single 90-inch panel won’t cover a wider window with fullness. You’d need two panels or a wider size. Measure your track first and calculate the fullness factor before ordering.
Should I measure before or after installing the pole?
After, ideally. The drop and width both depend on the pole’s exact position, including its height and how far it extends past the window. Measuring before installation means guessing at the final placement. If the pole isn’t up yet, mark the planned position and measure from that, not from the glass.
Can I shorten curtains that are too long?
References & Sources
- Home Depot. “How to Measure Curtains.” Covers measuring width from the rod and standard fullness guidance.
- Dunelm. “How to Measure for Curtains Buying Guide.” Details drop measurement by heading type and clearance rules for radiators.
