How to Install a Bathroom Medicine Cabinet | Studs, Level, and Solid Anchors

Installing a bathroom medicine cabinet means fastening it securely to wall studs or blocking, keeping it perfectly level, and checking the door swing before you drill.

Whether you’re replacing a dated unit or adding storage, the process for how to install a bathroom medicine cabinet splits into two paths: surface-mount cabinets screw directly to the wall, while recessed units sit inside a framed opening. Both start with the same priorities—finding solid wood behind the drywall, confirming the unit is level, and using the hardware that came in the box.

Surface-Mount Basics: Mark, Drill, and Drive Screws

A surface-mount cabinet is the simpler install because it hangs on the front of the drywall. Hold the cabinet against the wall at your chosen height, make sure the door can open fully without hitting anything, and use a level to confirm the top edge is true—cabinet doors bind and sag if the box sits even slightly crooked.

Once it’s positioned, trace the outline on the wall and mark the mounting holes. A stud finder is essential here; Home Depot’s installation guide says to center the cabinet on a stud when possible, then drill pilot holes and secure it with screws. If the holes don’t line up with studs, you can use drywall anchors for a lightweight cabinet, but a heavy unit needs the holding power of wood.

  • Locate studs with a finder and mark their centers.
  • Level the cabinet and trace its outline.
  • Mark the mounting holes and drill pilot bits.
  • Drive the screws with the supplied hardware, then reinstall shelves and the door.

If you’re shopping for a new unit before starting, our tested roundup of the best wall-mounted bathroom medicine cabinets compares models that are easy to hang and built to last.

Recessed Install: Cut the Opening, Add Blocking

Recessed cabinets look built-in but demand more prep because they live inside the wall cavity. Start by cutting a small test opening between studs to check for plumbing or wiring before you commit to the full cut—this single step prevents the most expensive mistake in the whole job.

Measure the rough opening carefully. One manufacturer’s guide specifies the opening width as the cabinet width minus 3/4 inch and the height as the cabinet height minus 5/8 inch, which leaves room to shim and level the box. If the opening doesn’t align with studs, add horizontal 2×4 blocking at the top and bottom so the cabinet has solid support to screw into.

Before cutting, determine whether the wall is load-bearing; if it is, a header may be required to maintain structural integrity. This Old House’s guide describes driving drywall screws through the cabinet’s side holes into the blocking, then reattaching the door carefully to avoid bending the hinges.

Height, Leveling, and Common Mistakes to Avoid

There’s no universal code for medicine cabinet height, but a practical rule is to mount it so you can see your face and shoulders in the mirror, often around 60–65 inches to the center or 72 inches to the top of the box. Test the height with the door open before you commit to holes.

Most installation failures trace back to a few avoidable errors. Skipping the stud finder, skipping the level check, and drilling without knowing what’s behind the drywall top the list. For recessed units, failing to add blocking or cutting through hidden pipes ranks just as high.

Mount Type Key Steps Most Common Mistake
Surface-mount Level, mark studs, pilot holes, drive screws Using anchors where studs are needed
Recessed Test cut, frame opening, add blocking, secure Cutting without checking for pipes or wires

For lighted or electrical models, disconnect the power before removal or installation—never work on a live circuit. If you can’t identify studs or the wall layout seems uncertain, consult a professional rather than guessing.

FAQs

What tools do I need to install a medicine cabinet?

You’ll need a stud finder, level, tape measure, pencil, drill with pilot bits, and a drywall saw or oscillating tool for recessed installs. Screws come with most cabinets, and 2×4 lumber is required if you’re adding blocking between studs for a recessed unit.

Can I install a medicine cabinet without hitting a stud?

Yes, but only for lightweight cabinets and only with drywall anchors rated for the weight. A heavy cabinet filled with toiletries needs the support of wood studs or blocking. If no studs align with the mounting holes, add blocking inside the wall before fastening.

How long does a medicine cabinet installation take?

A surface-mount cabinet typically takes 30 to 60 minutes, including locating studs and leveling. Recessed installs run longer—usually two to three hours—because cutting the opening, adding blocking, and fitting the box into the wall require more care.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.