Build a magnetic picture frame by gluing magnets into recessed holes so the two halves snap together around your artwork.
Making a magnetic picture frame solves a small but real annoyance: the ritual of unscrewing a frame, swapping the photo, and tightening it back down. With paired magnets embedded in the frame edges, you just pull the halves apart, slide in new art, and let them snap shut. The build takes an afternoon, uses hardware-store materials, and works for everything from kids’ drawings to gallery prints.
What You Need To Build A Magnetic Frame
Most DIY magnetic frames are built from wood strips, with magnets countersunk into the edges so the frame splits into two halves. Gather these materials before you start:
- Wood or pine strips (about 1 inch wide) cut to the length of your artwork
- Small neodymium or craft magnets — at least four
- Strong adhesive like E6000 or super glue
- Drill with a Forstner bit sized to your magnets
- Ruler, pencil, saw, and sandpaper
- Hanging hardware — picture hangers, eye hooks, or wire
For a lightweight variation, you can skip the wood entirely. Crayola’s locker frame craft uses a small frame with magnets glued to the back, so it sticks to any metal surface like a refrigerator.
How To Assemble The Frame Halves
Measure the artwork first, then cut four wood pieces — two for each side of the frame.
Drill shallow recesses only as deep as the magnets are thick. A Forstner bit creates a clean flat-bottomed hole that seats the magnet properly. If the magnet sits proud of the surface, the frame halves won’t close flat.
Glue each magnet into its recess with a strong adhesive. Don’t use hot glue — Crafty Nest found it weaker than super glue for this job, and Apartment Therapy warns that strong magnets need something “really strong, like E6000.” Before the glue sets, double-check your polarity: Resene explicitly warns that positive and negative sides must face each other, or the frame halves will repel instead of snapping shut.
Magnetic Tape And Backing Alternatives
Not every magnetic frame needs drilled holes. A simpler approach uses a standard picture frame plus magnetic sheet or tape applied to the back. This works in two ways:
- On a metal surface: attach magnetic tape to the frame’s back so it sticks to a refrigerator, locker, or metal wall panel.
- As an interchangeable insert: glue magnetic sheeting to the frame backing, then mount your photo on a thin steel or magnetic paper insert that swaps in and out.
When working with magnetic tape, let the adhesive cure for a full 24 hours before hanging anything — this is also a critical step if you glue magnets onto the back of a mini frame. Kids can paint or decorate the frame while the adhesive sets.
Tips For Hanging And Everyday Use
Add hanging hardware before you mount anything on the wall. Picture hangers, eye hooks with string, or wire all work, depending on how heavy the finished frame is.
If your plan involves drilling acrylic instead of wood, take extra care. HGTV recommends taping the corners, clamping the acrylic to scrap wood, and pressing straight down while drilling so the material doesn’t crack. The same advice applies to the backing plate if you’re using acrylic as the front surface.
One note on safety: strong magnets snap together with real force and can pinch skin, so keep them away from small children and pace yourself when assembling the halves.
For a ready-made version that skips the workshop entirely, our picks are in this acrylic magnetic photo frame roundup — tested options that swap photos just as easily.
| Method | Best For | Key Detail |
|---|---|---|
| Wood frame with countersunk magnets | Wall art, larger prints | Drill holes 4 cm from ends, glue magnets flush |
| Magnetic tape on frame back | Refrigerators, lockers, metal surfaces | Allow 24 hours for adhesive to cure |
| Magnetic sheeting insert | Quick photo swaps, kids’ art | Mount art on a steel or magnetic paper insert |
| Mini frame with magnets glued to back | Fridge magnets, locker decor | Needs at least two magnets on the back |
FAQs
What size magnets should I use for a picture frame?
Small neodymium disc magnets, roughly 6–10 mm wide and 2–3 mm thick, work well for most DIY frames. The exact size depends on your wood strip width and the frame’s weight. Thicker, stronger magnets are needed for larger frames, but they require deeper recesses so they sit flush.
Can I use hot glue to secure the magnets?
Hot glue is the weakest option and tends to fail on strong magnets because the bond stays brittle. Super glue or a two-part epoxy like E6000 holds far better. If you’re in a pinch, sand the magnet surface lightly before gluing so the adhesive grips.
Why won’t my magnetic frame close properly?
A frame that won’t close usually has one of two problems: the magnets are seated too deep so the halves can’t touch, or the polarity is mismatched so they repel each other. Recheck that the positive sides face the negative sides, and that each magnet sits flush with the wood surface.
References & Sources
- Apartment Therapy. “How to Make a Magnetic DIY Frame for Artwork in 10 Minutes.” Covers frame sizing, magnet placement, and adhesive recommendations.
- Crayola. “Locker Magnet Picture Frames Craft.” Details the mini-frame approach with magnets on the back for lockers and fridges.
- Resene. “Hang It Up — Magnetic Photo Frames.” Provides exact drilling dimensions and the polarity warning for frame halves.
