A wire loom is a protective tubing or sleeve that bundles and shields wires from abrasion, heat, and moisture.
For the full breakdown, see our best 1/2 Inch Flame Retardant Split Wire Loom Tubing guide.
Whether you’re tidying up a desk or rewiring an engine bay, a wire loom is the flexible covering that keeps cables organized and safe. Also called split loom tubing, convoluted tubing, or cable sleeving, it wraps around a bundle of wires to guard against physical damage, heat, and moisture. The term sometimes gets mixed up with “wire harness,” but a loom typically refers to the protective covering itself, while a harness is the full assembly of wires and connectors.
How Wire Loom Works
Split loom tubing is the most common type. It has a slit running along its full length, letting you open it and press a wire bundle inside. Once the wires are seated, the slit closes back up. You can reopen it later to add or remove wires, which makes it ideal for projects that change over time.
When you bend or twist the tubing, the slit stays shut, holding the wires securely. The material is flexible enough to route around corners, yet tough enough to stand up to vibration and abrasion.
Wire Loom Materials and Temperature Ratings
Wire loom comes in several materials, and the choice matters far more than most people expect. The outer covering determines how well your wires survive heat, UV exposure, and physical wear.
- Nylon — the most common choice for automotive use. Remington Industries’ nylon split loom is rated from -40°C to 125°C (-40°F to 257°F), with short-term exposure up to 150°C (302°F). It also meets the FMVSS 302 flammability standard.
- Polyethylene — a budget-friendly option with a typical operating range of -40°C to 105°C, per Electriduct’s published specs.
- Heat-shrink tubing — a snug, permanent wrap that shrinks tight around the bundle when heated.
- Braid and tape — braided sleeving offers flexibility and abrasion resistance, while tape adds a lightweight protective layer.
High-temperature split nylon loom from DigiKey and Kable Kontrol handles up to 300°F (149°C) and meets UL-94 HB flame-test requirements. For engine bays and other hot spots, always check the published temperature and flammability ratings before you buy.
Sizing: Picking the Right Diameter
Wire loom is sized by nominal diameter, which refers to the inner opening. Choosing the wrong size is the most common mistake. Too small and the wires get pinched or impossible to insert; too large and the bundle rattles around, defeating the whole purpose.
The table below shows common sizes from Remington Industries’ nylon split loom datasheet, with actual inside and outside diameters:
| Part Number | Inner Diameter | Outer Diameter |
|---|---|---|
| 1/4NYBLA | 0.281″ | 0.378″ |
| 3/8NYBLA | 0.421″ | 0.535″ |
| 1/2NYBLA | 0.518″ | 0.675″ |
| 3/4NYBLA | 0.762″ | 0.933″ |
| 1NYBLA | 0.917″ | 1.114″ |
Nelco Products also lists sizes up to 1-1/2″ nominal, so there’s a fit for nearly any bundle. A good rule of thumb: measure the wire bundle’s actual diameter with a caliper, then pick a loom size slightly larger than that measurement.
If you’re shopping for a specific size, our tested roundup of the best 1/2-inch flame retardant split wire loom tubing can help you compare top options.
Where People Use Wire Loom
Automotive work is the most common application. Engine bays expose wires to heat, vibration, oil, and abrasion, and split loom handles all of it. But the same tubing works just as well for home theater setups, computer builds, and any spot where a tangle of cables needs wrangling.
One honest caveat: split loom is flexible sleeving, not rigid conduit. It won’t stand up to heavy impacts or crushing forces. If you need hard pipe protection, look at conduit instead. Also, the cut edge of split loom can be sharp — a fresh cut can scratch your fingers, so a small tool or a bit of tape on the end helps during installation.
When you buy, match the material to the environment. Nylon and high-temp options handle engine heat and UV exposure; standard polyethylene works fine indoors but may not survive years of direct sunlight. Checking the datasheet takes seconds and prevents a melted, cracked, or brittle mess later.
References & Sources
- Remington Industries. “Nylon Wire Loom Tubing Data Sheet.” Published temperature, flammability ratings, and dimensional specs for nylon split loom.
- Wikipedia. “Cable Harness.” Background on harness versus loom terminology and construction methods.
- McMaster-Carr. “Wire Looms.” Product category covering loom types, materials, and sizing options.
