How to Cover Above Ground Pool for Winter | Step-By-Step Closeout

Covering an above-ground pool for winter starts with cleaning and balancing the water, then lowering it, adding a pillow, and securing the cover snugly with its cable and winch.

Closing a pool properly keeps spring opening easy. A cover that flaps, sags, or tears over winter creates a mess you will deal with for months. The process takes a few hours, but doing it correctly means the water stays clean and the cover survives until next year. This guide walks through the whole sequence with exact steps and settings.

How to Cover Above Ground Pool for Winter: The Full Process

The job has five stages: clean and balance the water, lower the level, add a pillow, lay out and secure the cover, then check it through the season.

Clean the Water and Add Winter Chemicals

Brush walls and floor, vacuum, and skim the surface. Balance pH, alkalinity, and sanitizer to normal ranges before adding winter chemicals like a closing kit. ARM & HAMMER’s pool closing guide recommends shocking the pool and adding a winter algaecide, but wait until the shock level drops before putting the cover on—direct contact with fresh chemicals can degrade the cover material.

Lower the Water Level

The right water level depends on your cover and skimmer setup. With a skimmer cover plate, water can stay at its normal level; otherwise, lower it just below the skimmer opening. Leslie’s winter cover tips advise watching the level and adding water if it drops more than an inch, since a falling level stresses the cover and walls. Remove ladders, rails, and accessories before starting, and winterize the pump and filter per your equipment’s instructions.

Install the Pool Pillow and Lay Out the Cover

An air pillow (ice equalizer) sits in the pool’s center under the cover, absorbing ice expansion pressure so the cover and walls don’t take the strain. Leslie’s recommends inflating the pillow only halfway—a fully inflated pillow can burst when ice presses against it. Place it in the middle before the cover goes on.

Spread the cover to form a loose pyramid over the pillow, letting it fall evenly onto the water around the whole circumference. It should rest directly on the water’s surface everywhere; if suspended or baggy, pull it into position.

Installation Step What to Do Common Mistake
Water level Lower below skimmer unless using a cover plate; keep at least 6 inches from top edge Letting the level drop too far over winter
Air pillow Inflate to about 50% and center it under the cover Overinflating, which leads to bursting under ice pressure
Cover placement Form a loose pyramid, let it fall evenly onto the water Leaving it suspended or bunched on one side
Securing Thread cable through grommets, tighten snugly with winch or turnbuckle Overtightening, which stresses the cover and walls
Sharp edges Pad any protrusions on the pool or cover hardware Leaving edges exposed to tear the cover

Secure the Cover With the Cable and Winch

Most above-ground covers use a vinyl-coated cable threaded through edge grommets, tightened with a winch or ratchet. Lay the cover flat, thread the cable through every grommet, then place it over the pool; Wholesale Pool Covers’ guide spells out two setups.

Turnbuckle setup: open the turnbuckle until only screw ends show inside. Run the cable through each screw loop, secure with cable clamps, then tighten the turnbuckle so the cover is snug.

Winch setup: insert one cable end into one side of the winch hole and spindle, turn a few times, insert the other end, pull it through, then crank tight.

Snug is the goal, not tight—an overstressed cover can tear at grommets or pull walls inward. For straps, clips, sandbags, or seal wrap, follow the same principle: secure evenly so it can’t flap, but don’t stretch it. Cover the skimmer opening if used, and pad sharp edges with foam or tape.

When ready to shop, our tested roundup of the best winter pool covers compares top models.

Winter Maintenance and Safety Notes

Check the cover every few weeks. If water drops more than an inch, add water through the cover with a hose. Pull heavy snow off before it stretches the cover or strains the cable system.

A winter cover is not a safety cover unless specifically labeled as such—it won’t support a person’s weight, as The Swim’s tips emphasize. Keep the cover free of standing water and debris, and your pool will open clean.

FAQs

How much should I inflate a pool air pillow?

Inflate to about half capacity. Leslie’s says a halfway-inflated pillow absorbs ice expansion without bursting; a full one can pop under ice pressure, leaving the cover and walls unprotected.

Can I use a winter cover as a safety cover?

No, unless explicitly labeled as a safety cover. Standard winter covers keep out debris but aren’t designed to hold a person’s weight. Buy a safety-rated cover if you need access prevention.

How do I stop the cover from blowing off in the wind?

Keep it resting evenly on the water with no suspended areas, and ensure the cable or straps are snug but not overstressed. Even overhang catches less wind and wears more slowly.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.