For a 48-inch window, buy a 64 to 68-inch curtain rod and panels totaling 72 to 96 inches in width.
Measuring for a 48-inch window is straightforward once you grasp the two-step order: width first, then length. Getting the width right matters most, because that determines whether your curtains look full and intentional or stretched thin. The process takes about five minutes with a steel tape measure, and the payoff is panels that hang exactly as you pictured them.
The Width Rule For A 48-Inch Window
Treat 48 inches as your starting window width, then add rod overhang on both sides. Home Depot’s curtain guide recommends extending the rod 8 to 10 inches past each side of the frame, which gives you a 64 to 68-inch rod for a 48-inch window.
That overhang serves two purposes: it lets the panels stack neatly off the glass when open, and it makes the window feel wider than it is. Measure the rod span left to right, not just the glass, and skip the decorative finials at the ends—Dunelm and other guides explicitly say to measure the functional rod or track width only.
Fullness: How Wide Should The Panels Be?
Curtains look best at 1.5x to 2x the rod width, a rule echoed across Home Depot, Wayfair, and Port & Bay guides.
| Look | Total Panel Width | Per Panel (Two Panels) |
|---|---|---|
| Minimum fullness (1.5x) | 96 inches | 48 inches each |
| Fuller look (2x) | 136 inches | 68 inches each |
| Trim coverage (1.5x of window) | 72 inches | 36 inches each |
Rod Position: Height And Overhang
Mount the rod 4 to 6 inches above the window frame, and extend it 4 to 6 inches beyond each side per standard retail guidance.
The higher mount draws the eye upward and makes ceilings feel taller. Just confirm the rod brackets sit into studs or use quality anchors, since a wide rod carrying two heavy panels needs solid support.
Measuring Length: Sill, Below Sill, Or Floor
Length depends entirely on where you want the hem to land. Measure from the top of the rod (not the finial) to your chosen endpoint.
- Sill length: measure from the rod to the window sill, then add roughly 1 inch so the hem clears the sill without dragging.
- Below-sill length: measure from the rod to about 4 inches below the sill, a popular compromise in kitchens and bathrooms.
- Floor length: measure from the floor to the top of the rod, then subtract about 1 inch so the hem floats just above the floor.
Common Measuring Mistakes To Avoid
The most frequent errors are simple and easy to catch. Measuring only the glass instead of the full frame or planned rod span leaves your curtains short. Grabbing the tape at the finial instead of the rod’s functional width adds inches you don’t have. And ordering panels without accounting for fullness leaves you with curtains that lie flat and lifeless.
Write both numbers down before you shop, and always list width first, then length.
Before you order, check our roundup of the best 48-inch curtains for tested picks that match these measurements.
FAQs
Should I measure the window or the rod for curtain width?
Measure the planned rod span, not the window itself. A 48-inch window needs a rod that extends 8 to 10 inches past each side, so the rod measurement lands between 64 and 68 inches. That overhang lets panels stack off the glass and frames the window properly.
How high above the window should the curtain rod go?
Mount the rod 4 to 6 inches above the window frame. This placement makes ceilings feel taller and prevents light from leaking over the top of the panels. For decorative outside-mount rods, measure length from where the rod actually sits, not from the top of the window frame.
What does 2x fullness mean for a 48-inch window?
References & Sources
- Home Depot. “How to Measure Curtains.” Rod overhang, floor-length measuring, and fullness guidance.
- Dunelm. “How to Measure for Curtains Buying Guide.” Eyelet allowance, radiator clearance, and finial exclusion rules.
- Homes & Gardens. “How to Measure for Curtains.” Width-first ordering format and rod positioning guidance.
