Install 4×8 fence panels by digging plumb post holes spaced to your panel’s exact width, then leveling each panel and fastening it with the manufacturer’s approved hardware.
Getting a preassembled panel fence straight depends on measuring the actual panel before you dig. A “4×8” panel rarely measures a true 48 inches by 96 inches, and post spacing that ignores the real width turns a weekend project into a crooked mess. The fix is to plan around the panel’s true dimensions, keep posts plumb while concrete cures, and let the panel’s installation sheet decide the fasteners—whether you’re fencing with wood pickets or vinyl sections.
Measuring And Laying Out The Post Spacing
The most common mistake is spacing posts from their centers. Panels mount to post faces, so a 96-inch panel needs posts spaced 96 inches apart measuring from the inside edges of those posts. The exception is panels designed to sit between posts, where spacing is edge-to-edge. Measure your panel’s actual width and the post’s thickness before marking anything.
For a typical 4×8 Collingwood scalloped picket panel, one manufacturer’s manual calls for post holes spaced 96 inches on-center with a roughly 2-inch gap from ground to panel bottom. Mark layout lines with a mason’s line and line level so every post lands in the same straight row.
Do not set every post before hanging panels. One trusted guide warns this turns a small measuring error into an unfixable gap. Install in sections: set a post, brace it, hang the panel, then move to the next post.
Digging Holes And Setting Posts Plumb
Before digging, call 811 so utility lines get marked. Drop the post in and use gravel to nudge it until perfectly plumb in both directions before adding concrete.
Patience pays here. After pouring concrete, verify the post is still level and let the concrete cure fully per manufacturer’s instructions before attaching panels. A post that shifts during cure will throw every panel after it out of line.
Attaching The Panels To The Posts
Hold each panel at the correct height using wooden blocks or spacers so it never rests on soil, which rots the base over time. Align the panel top with the post top.
Do not over-tighten screws, and check orientation—one manual notes top and bottom rail holes are different sizes, with larger holes facing down.
Keeping Panels Level Through The Whole Run
Check each panel is level before fastening, then check the next post with a level before backfilling or concreting. Once concrete sets, misalignment is permanent. A gap of about two inches between panel bottom and soil keeps moisture away from wood and extends fence life.
- Measure the panel’s actual width and the post thickness.
- Mark post locations based on the panel width measured from the edges of the posts.
- Call 811 to mark utilities, then dig holes 10–12″ wide and 36–42″ deep.
- Set the post plumb, pour concrete, and let it cure fully.
- Hang the panel on blocks at the correct height, level it, and fasten per the manufacturer’s hardware.
If you’re weighing material options before buying, our roundup of the best 4×8 fence panels available compares wood, vinyl, and metal picks side by side, with notes on which systems install fastest.
FAQs
Should I space fence posts 8 feet apart for 4×8 panels?
Yes, roughly. Measure the panel’s actual width first, because preassembled panels vary slightly from a true 96 inches. Space the post holes to match the panel’s real measurement, measuring from the inside edges of the posts where the panel will sit. If the panel is exactly 96 inches, set the posts 96 inches apart edge to edge.
Do I need to call 811 before installing a fence?
How far off the ground should a 4×8 fence panel sit?
Keep about a 2-inch gap between the bottom of the panel and the soil. That clearance keeps moisture and splashing dirt away from the wood or vinyl, which slows rot and decay at the base. Use spacer blocks while you hang the panel to hold the gap, then remove them once the fasteners are in.
References & Sources
- Home Depot Canada. “How to install prefab fence panels.” Details the bracing, mason’s line, and bracket-attachment workflow for preassembled panels.
- Home Depot. “How to Install a Fence.” Covers post-hole dimensions, 811 utility marking, and panel-fastening with brackets and screws.
- Collingwood Scalloped Picket Panel Manual. “4′ x 8′ Collingwood Scalloped Picket Panel Installation.” Specifies 96-inch on-center spacing and the 2-inch ground clearance for this panel model.
