How to Bead Pens | DIY Pen Crafting Steps

Beading a pen involves disassembling the pen, threading decorative beads onto the shaft, and reassembling it so the pen still writes smoothly.

Making beaded pens takes about twenty minutes once you have the right supplies. The trick is knowing which end to open and how much room to leave for the cap. The same basic workflow works for most beadable pen blanks and plain pens with removable tops.

What You Need to Make a Beaded Pen

  • Pen blank or beadable pen kit – the hollow outer casing that beads slide onto. Some kits have a removable top cap and separate ink cartridge.
  • Beads – holes must measure roughly 2 mm to 5 mm to fit over the pen shank. Decorative beads between 10 mm and 20 mm balance comfort and visual weight. The first bead may need to be 12 mm or larger to bridge a recessed section.
  • Spacers – optional for filling gaps and creating patterns.
  • Charm, tassel, or dangle – attached with a jump ring; flat nose pliers help close the ring securely.
  • Strong adhesive – E6000 or super glue for securing the end cap or focal bead. Use glue in a well-ventilated area.
  • Flat nose pliers – for gripping small hardware without scratching.

The Step-by-Step Method

The core sequence below works for most beadable pen styles. If your pen uses a different cap design, check the assembly guide that came with the kit.

  1. Disassemble the pen from the top end. Unscrew or gently pull off the top cap or decorative topper. Do not force the bottom or ink side apart.
  2. Remove the ink cartridge. Slide the refill out of the casing and set it aside.
  3. Test bead fit on the shaft. Slide one or two beads onto the empty pen tube before committing to a pattern. If they do not move freely, the bead holes are too small.
  4. Thread beads from the bottom up. Start at the end closest to the writing tip and work toward the top. Leave about 5 mm to 8 mm of bare threaded post at the top so the cap can screw back on securely. Overfilling is the most common mistake — if the cap will not seat, remove one bead.
  5. Secure the end bead or cap. Some kits let the top cap hold everything in place with friction. Others require a drop of adhesive on the final bead or cap threads. Apply glue sparingly.
  6. Reinsert the ink cartridge and test. Push the refill back in, screw the tip on, and write a test line before the glue cures. If the pen skips or beads shift, adjust. If everything works, let the adhesive cure fully — one tutorial recommends 24 hours before handling or gifting.

Common Mistakes and How to Avoid Them

  • Opening the wrong end. Always work from the top or decorative end. Forcing the bottom apart can bend the ink cartridge or crack the casing.
  • Skipping the fit check. Test one bead before threading any pattern.
  • Not leaving cap space. Beads that go to the top mean the cap will not tighten, causing leaks or breakage.
  • Making it too heavy. Large stone or metal beads make the pen uncomfortable to write with. Keep the design light enough to sit upright in a cup.
  • Using glue before testing. Test the whole assembly — writing included — before you seal anything.
  • Over-tightening beads. Leave a hair of wiggle room to avoid stress on the tube or cracked beads.

For supplies, see our tested roundup of the best beads for pens, covering hole sizes, material weight, and patterns for standard pen blanks.

Adapting the Method for Different Pen Styles

Beadable pen blanks are designed for this craft, with a removable top cap, visible threading, and a smooth central tube. These are the easiest option for beginners.

Plain store-bought pens can work if the top cap unscrews or pops off. Check whether the decorative surface is part of the ink cartridge housing or a separate sleeve. If the beadable section is glued, you may need to cut it off with a craft blade.

Wrap-style designs use beading wire or stretch cord wrapped around the pen body, skipping the hole-size limit but requiring strong adhesive to prevent spinning. The thread-on method holds up better to daily use.

FAQs

What kind of glue works best for beaded pens?

E6000 is the most common because it dries clear and flexible. Super glue works for quick fixes but can be brittle. Let adhesive cure for at least a few hours before testing.

Can I use any beads for a beaded pen?

Only beads with holes between roughly 2 mm and 5 mm will slide onto a standard pen shank. Pony beads, tiny seed beads, and most 6/0 or 8/0 glass beads fit. Large-hole gemstone beads often work, but check weight.

Why won’t my pen cap screw back on?

You threaded too many beads or did not leave enough bare post at the top. Remove beads one at a time and test fit until the cap seats fully with about 5 mm to 8 mm of clear threaded area.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.