Installing a 370Z front lip requires drilling the bumper for riv-nuts, applying double-sided tape, and securing it with bolts and screws.
Understanding how to install a 370Z front lip correctly means drilling the bumper for riv-nuts and letting the adhesive cure fully before driving. The process works on all non-NISMO 370Z bumpers from 2009 to 2020, and the specific hardware and tools depend on whether your lip is ABS plastic, polyurethane, or carbon fiber. If you’re still choosing a part, our top 370Z front lip recommendations cover tested options for each material type.
What Tools Do You Need for the Job?
ABS lips need riv-nuts drilled into the bumper for a solid mechanical hold. Polyurethane lips are more flexible and benefit from heat application in cold weather. Carbon fiber requires specific adhesive protocols. The table below covers the essentials for a standard ABS or polyurethane install on a non-NISMO bumper.
| Item | Purpose |
|---|---|
| 2 OEM bumper bolts | Reused to secure center of lip |
| 2 riv-nuts | Installed into drilled center holes for bolted hold |
| 6 self-tapping screws | Secure corners of the lip |
| 2 M6 flanged bolts + nuts | Final center fastening at riv-nut points |
| 1‑inch double‑sided tape | Primary adhesive between lip and bumper |
| Jack + 2 jack stands | Raise and support the front of the car |
| 3/8″ drill bit + riv‑nut tool | Drill holes and set riv-nuts into the bumper |
| Heat gun or hair dryer | Warm polyurethane lips in cold weather |
| Rubbing alcohol + Scotch‑Brite pad | Clean and scuff the mounting surface |
Installing a 370Z Front Lip: Step-by-Step Process
The official steps from Z1 Motorsports’ installation guide outline this sequence for ABS and polyurethane lips on non-NISMO bumpers.
Step 1 — Prep and lift. Put the transmission in Park (Reverse for manuals), set the parking brake, lift the front at the proper jacking points, and support it on jack stands.
Step 2 — Remove factory trim. Take out the two bolts on the bottom of the front bumper. Pull the plastic bumper trim — held by plastic rivets — with pliers and discard the rivets.
Step 3 — Clean the surface. Spray detailing cleaner to remove loose debris, then wipe the mounting area with rubbing alcohol on a Scotch‑Brite pad to remove wax and residue. This step determines whether the tape holds long‑term.
Step 4 — Test fit and mark holes. Loosely secure the lip with the two OEM bolts. Hold it against the bumper and mark the two center hole positions with a marker. Remove the bolts and set the lip aside.
Step 5 — Drill and install riv‑nuts. Drill two holes at the marks with a 3/8″ bit. Use a riv‑nut tool to install riv‑nuts into those holes, creating threaded anchor points in the bumper.
Step 6 — Apply tape and mount. Peel back the protective shielding on the double‑sided tape slightly. Align the lip carefully and press it firmly onto the bumper. Tighten the two OEM bolts into the riv‑nuts.
Step 7 — Secure corners and center. Drive six self‑tapping screws into the pre‑marked corner holes. Use the M6 flanged bolts and nuts at the center points for final securement.
Step 8 — Cure. Do not drive or wash the car for 24 hours. The adhesive needs a full set, and wind force at highway speeds can pull the lip loose if you rush it.
Polyurethane lip tip: Remove the bumper entirely for easier flex around the wheel arches. Warm the lip with a heat gun if it feels brittle. Apply tape and screw the rear sections where the lip wraps around. Leave overnight to set.
Common Mistakes That Ruin an Install
Painting polyurethane lips before installation. The material flexes and standard paint cracks. Install unpainted, then use flexible paint afterward.
Skipping surface prep. Alcohol and a Scotch‑Brite pad remove wax and residue. Without this step the tape loses adhesion within weeks.
Over‑tightening screws. ABS lips crack under excessive torque. Snug is enough. Over‑driving self‑tappers also damages the bumper fascia.
Installing polyurethane in cold weather without heat. The material turns brittle below about 50°F. A heat gun restores flexibility for a clean fit around curves.
Driving or washing within 24 hours. The tape needs a full cure cycle. Wind pressure at speed and water intrusion both weaken an unset bond.
FAQs
Does a front lip fit all 370Z models?
It fits all non‑NISMO 370Z bumpers from 2009 to 2020, including the post‑facelift 2013+ models. NISMO bumpers use different fascia geometry and require a specific NISMO lip.
Can I install a 370Z front lip by myself?
A two‑person installation is strongly recommended. One person holds the lip in position while the other marks holes and drives fasteners. Solo alignment is possible but much harder to get symmetrical.
Will a front lip affect my warranty?
Aftermarket modifications may void warranty coverage on affected components. Check your vehicle’s warranty terms for body panel and fastener modifications.
References & Sources
- Z1 Motorsports. “Z1 370Z ABS Front Lip Installation Instructions.” Official installation steps and hardware specifications for ABS and polyurethane front lips on the 370Z (Z34).
