How to Install a 15 Gallon Fuel Cell? | Mounting & Plumbing Guide

Installing a 15-gallon fuel cell requires steel-bracket mounting, a rollover vent valve, AN-fitted supply and return lines, and chassis grounding for safe operation and accurate gauge readings.

Installing a 15-gallon fuel cell in a race car, drift car, or off-road vehicle comes down to four critical steps: secure mounting to the frame, proper venting, correct AN fittings, and solid chassis grounding. The most common mistakes — relying on the cell’s factory tabs for structural support, skipping the rollover valve, and routing lines near heat — are all avoidable with the right sequence. Before starting, it helps to compare the available models — our roundup of the best 15-gallon fuel cells covers the top options for different builds.

Begin by disconnecting the negative battery terminal, loosening the gas cap to relieve pressure, and draining the existing fuel tank. Work in a well-ventilated area with no ignition sources — fuel vapor is highly flammable.

Installing A 15-Gallon Fuel Cell: Where To Mount It

Choose a location in the trunk or rear bed with at least a few inches of clearance from exhaust components, suspension parts, and drivetrain elements.

Use steel mounting brackets or straps bolted directly to the frame or a reinforced floor pan. Most cells come with a pre-formed flange containing eight bolt holes — use all of them. Never rely on the aluminum cell’s factory tabs for structural support; they are assembly aids and can tear under the weight of a full tank. The cell must not shift under hard cornering or off-road forces.

For professional racing, a rubber/molded cell with FIA-FT3 approval (such as the Enduro Cell ED115) is required. For street and off-road use, an aluminum cell like the Race Safe RS215-AEF works well, costs less, and still meets safety requirements when installed correctly.

Fuel Lines, Vent Valve, And Fittings

Install a rollover vent valve on the cell’s dedicated vent port to prevent vapor pressure buildup. Route the vent hose upward and away from exhaust, headers, and other heat sources, with a fuel-safe filter at the end. A blocked or kinked vent can cause fuel starvation or tank collapse.

Use -6 AN fittings for the supply line and -8 AN for the return line, with high-quality hose rated for gasoline and ethanol. Tighten all AN fittings to the manufacturer’s torque spec — hand-tight is not enough. Verify that your fuel pump and engine rail use compatible AN sizes before final assembly.

The JEGS fuel cell installation guide provides detailed torque specs and routing diagrams for common setups.

How Do You Ground And Leak-Test A Fuel Cell?

Ground the fuel cell body to the vehicle chassis with a dedicated ground strap — this prevents static discharge that can ignite fuel vapor and ensures the sending unit reads accurately. Connect the sending unit’s center terminal to the fuel gauge wire, and run a separate ground from the sending unit’s outer bolt to the frame.

Before reconnecting the battery, check every fitting, hose end, and the cap gasket for tightness. Confirm the vent is unobstructed, all brackets are secure, and the cell cannot shift. Then add fuel and inspect for leaks at every connection. Common installation mistakes include mounting the pump too close to the tank (which causes cavitation and hot fuel delivery), routing lines close to the exhaust, and reconnecting the battery before leak-testing.

The table below compares the two standard 15-gallon fuel cell choices and their best applications.

Feature Race Safe RS215-AEF Enduro Cell ED115
Material Aluminum Rubber / Molded
Capacity 15 gallons 15 gallons
FIA-FT3 Certified No Yes
Best Application Street / Off-Road Professional Racing
Standard Fittings -6 AN / -8 AN -6 AN / -8 AN
Sending Unit Included Included
Mounting Pattern 8 bolt holes 8 bolt holes

Whichever cell you choose, the installation sequence is the same: mount securely with steel brackets, install the rollover vent, plumb with AN fittings, ground to the chassis, and leak-test before running the engine.

FAQs

What size AN fittings does a 15-gallon fuel cell use?

Most 15-gallon fuel cells come with standard -6 AN and -8 AN ports. Supply lines typically use -6 AN, while return lines use -8 AN. Verify that your fuel pump and engine rail use compatible sizes before making final connections to avoid flow restrictions.

Can I install a fuel cell in a street-legal vehicle?

Yes, with proper venting, a secure cap, and chassis grounding. For street use, an aluminum cell like the Race Safe RS215-AEF is sufficient and does not require FIA certification. Check your local regulations for any additional requirements on fuel system components.

Do I need an FIA-certified fuel cell for my build?

FIA-FT3 certification is required only for professional racing events. For street cars, drift cars, and off-road vehicles, a non-certified aluminum 15-gallon cell provides the same functionality at a lower cost without sacrificing safety when installed and grounded correctly.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.