Adding a second lock to a front door means installing a single-cylinder deadbolt 6 to 12 inches above the existing handle, requiring a 2⅛-inch hole saw for the bolt and a 1-inch hole for the latch on the door edge.
A deadbolt sitting six inches higher than your key-in-knob lock turns a flimsy push-in lock into a real barrier. The job itself runs about an hour with a drill and a chisel, but the difference in break-in resistance is massive—that second bolt stops kicks and pries at the weak spot. Here’s the sequence that works.
Picking the Right Lock Type and Position
Most US residential doors are 1¾ inches thick and accept a single-cylinder deadbolt as the standard second lock. The deadbolt body needs a 2⅛-inch hole, and the latch needs a 1-inch hole on the door edge. Measure the backset—the distance from the door edge to the center of the existing lock hole—to confirm the new lock matches. Common backsets are 2⅜ inches or 2¾ inches. If your door can’t accept a new hole, a surface-mounted high-security lock is the alternative; it requires chiseling a ⁵⁄₁₆-inch recess into the door surface.
Where to place it: Mark the door at roughly 44 inches from the bottom, or 6 to 12 inches above the existing handle. Tape the manufacturer’s paper template to the door at that exact height, then mark the center for both the deadbolt cylinder and the latch bolt. A misaligned template is the most common reason the bolt won’t connect with the latch later, so take the extra thirty seconds to check the template against a level.
Drilling and Fitting the Deadbolt
Drill the 2⅛-inch cylinder hole through the door face, stopping when the bit breaks through the opposite side, then finish drilling from that second side. This two-sided method prevents the wood from splintering—drilling straight through from one side usually blows out the back face. Then drill the 1-inch latch hole on the door edge, making sure it connects cleanly with the main cylinder hole.
Recessing the faceplate: Slide the latch into the edge hole, trace the faceplate outline with a pencil, and chisel a shallow recess so the faceplate sits flush with the door edge. A faceplate left proud keeps the door from closing fully. The recess depth is roughly the thickness of the faceplate itself—chisel ¹⁄₁₆ inch at a time and check the fit.
Push the deadbolt through the large hole to connect with the latch, then attach the inside and outside plates. Tighten the screws firmly but not so hard that you strip the door’s wood or warp the metal plates.
Once the lock is in and the door gear installed, if you are ready to buy, check out our tested product roundup of the best additional locks for front doors to see which models hold up best against real kick-in tests.
Anchoring the Strike Plate for Real Security
This step makes or breaks the whole install. Close the door and mark where the deadbolt latch strikes the door jamb.
Trace the strike plate, chisel a groove so it sits flush with the jamb, then drill the center hole for the bolt. Here’s the non-negotiable part—the screws that come with most locks are ¾ inch and only bite into the jamb trim. Replace them with 2½- to 3-inch screws that anchor into the door frame stud behind the trim. Those long screws are what actually stop a shoulder from breaking through.
Testing the fit: Open and close the door several times. The bolt should slide freely without sticking. If it sticks, the strike plate recess is too shallow—remove a little more wood with the chisel. If the mechanism feels dry after the test, apply a small amount of lubricant to the bolt. Also verify the thumb-turn on the inside rotates easily in case of a fire.
| Installation Step | Key Detail | Common Mistake |
|---|---|---|
| Mark position | 44 inches from floor (6–12 inches above handle) | Template misalignment → bolt misses latch |
| Drill cylinder hole | 2⅛-inch hole saw, drill halfway from each side | One-side drilling splinters the door face |
| Drill edge hole | 1-inch bit, connects to main hole | Hole too shallow → latch won’t engage |
| Recess faceplates | Chisel flush with door edge or jamb surface | Faceplate proud → door won’t close |
| Install strike plate | Use 2½–3 inch screws into frame stud | Short screws only bite the trim (useless) |
| Test bolt movement | Slides freely without sticking | Strike recess too shallow → bolt binds |
FAQs
Can I install a second lock on any door?
Solid wood or metal doors 1¾ inches thick accept the standard drill-and-install method. Hollow-core interior doors or doors with visible rot or damage cannot hold a secure lock and should be replaced first.
What tools do I need besides a drill?
A 2⅛-inch hole saw, a 1-inch drill bit, a screwdriver, a chisel and mallet, a tape measure, a pencil, and the lock’s paper template. The chisel is essential for recessing the faceplate and strike plate flush with the surface.
Do smart locks require different installation steps?
The drilling and mounting steps are nearly identical to a standard deadbolt. The difference is wire connection between the interior and exterior panels plus battery installation. The manufacturer’s app will guide the pairing process on iOS or Android.
References & Sources
- This Old House. “How to Upgrade Your Front Door Hardware.” Details deadbolt placement height and step-by-step installation.
- Lowe’s. “How to Install a Lockset.” Covers hole drilling, backset measurement, and strike plate recessing.
