How to Install Underwater Boat Lights? | Transom Mount Method

Install underwater boat lights below the waterline on a flat transom, using marine sealant, a pilot hole, and a fused 12V connection.

Learning how to install underwater boat lights starts with choosing the right spot on the hull, then cutting and sealing the hole, and finally wiring the fixture to your DC system. If you’re still picking out lights, our roundup of the best boat underwater lights covers models suited to different hulls and budgets.

Where On The Hull Should You Mount The Lights?

Underwater lights mount below the waterline on a flat exterior surface of the transom or hull sides. The ideal location keeps the fixture submerged while avoiding trim tabs, outdrives, transducers, ladders, and outboard engines — anything that could block the beam or create turbulence.

Placement heights vary by model. Lumitec’s SeaBlazeX2 guide specifies 6–12 inches (150–300 mm) below the waterline and spacing between 1 and 3 feet. PowerBoat TV’s demo positioned lights 8 to 24 inches down. A common rule of thumb is at least 8 inches below the waterline, but always confirm with your specific light’s manual.

Mark the centerline on the outside of the hull, then inspect the inside for wiring, stringers, or obstructions before drilling. Flat surfaces are preferred — no manufacturer recommends placement on running surfaces. T-H Marine’s demo suggests positioning lights about one-third of the way in from each side for balanced illumination.

Cutting The Hole And Sealing The Fixture

Start with the template included with your light and drill a 1/8-inch (3 mm) pilot hole from the outside. Confirm the position from inside the hull before cutting the final opening — this prevents drilling into a stringer or hidden wire.

The final hole size depends on your fixture. OceanLED’s install guide calls for a 1/2-inch to 5/8-inch (12–15 mm) hole for cable passage. The BoatUS underwater light installation guide used a 2-3/8-inch hole for a thru-hull style light. Always follow your specific model’s template.

Light Type Below Waterline Mount Hole Size
Lumitec SeaBlazeX2 6–12 in (150–300 mm) 0.5 in (12.7 mm)
OceanLED 8+ in (200+ mm) 0.5–0.625 in (12–15 mm)
Thru-hull (BoatUS example) Below waterline 2.375 in (60 mm)
T-H Marine style ~1/3 in from each side Per template

Prepare the surface by sanding or grinding away bottom paint and gelcoat where the light will seat — sealant bonds best to bare fiberglass or metal. Old antifouling paint can react with aluminum housings, so removal is essential. Remove rough edges from the cut hole and clean the area.

Dry-fit the fixture and confirm cable routing before applying any sealant. Use a marine-grade below-the-waterline adhesive/sealant around the flange, cable entry, and any unused holes. Press the light into place and twist slightly to spread the sealant evenly, then wipe away excess. For thru-hull styles, secure the interior retaining nut or mounting hardware.

Wiring And Testing The Connection

Route the cable inside the boat to a switch or breaker, then to power. The positive lead must include an inline fuse or breaker at the correct amp rating for the light. Connect to the boat’s 12V DC circuit using marine-grade wire and waterproof connections. Lights rated for 24V are also common — confirm your model’s voltage before wiring.

Before returning the boat to the water, test the light and check for leaks. Hook up power briefly to confirm the fixture works, then inspect the seal from inside the hull. If the boat is on a trailer, running a garden hose over the transom helps verify the seal before full launch. Mercury Marine recommends hiring a certified marine technician if you lack experience drilling hulls — a poor seal creates a real leak risk. Take your time on preparation; a clean surface and proper sealant are what keep the water out.

FAQs

What size hole do I drill for underwater boat lights?

The size depends on your light model. OceanLED fixtures require a 0.5–0.625-inch hole for cable passage, while some thru-hull styles need a larger 2.375-inch opening. Always follow the template and spec sheet that came with your specific light.

Can I install underwater lights while the boat is in the water?

No. The boat must be hauled out, securely supported, and the work area completely dry before drilling or applying sealant. A dry, clean surface is essential for proper sealant bond and to prevent leaks.

Do I need a fuse for underwater boat lights?

Yes. The positive power lead must include an inline fuse or breaker at the correct amp rating for the light. This protects the wiring and fixture from electrical faults and follows standard marine wiring practice.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.