How to Make a Bandana Bib for Baby | Sew It In An Hour

A bandana bib for baby is a triangular drool bib made from two matching fabric pieces sewn right sides together, turned, topstitched, and finished with snaps or Velcro.

Teething drool stains every onesie, and store-bought bibs cost more than a decent yard of cotton. Sewing your own takes about one hour, uses basic machine stitches, and produces a bib that actually fits. The core method stays the same: cut two identical pieces, sew around most of the edge, turn it right side out, topstitch flat, then add a closure. No serger needed. This walkthrough covers the pattern, sewing, and closure options for a comfortable, adjustable bib.

What You Need To Sew A Bandana Bib

You need fabric, a sewing machine, thread, scissors or a rotary cutter, pins or clips, an iron, and a closure (KAM snaps or Velcro). Fabric choices matter. Cotton quilting fabric works well for the front; soft terrycloth or flannel on the back absorbs drool better. Some add a hidden PUL (polyurethane laminate) layer for waterproofing — but use clips with PUL because pins leave permanent holes. Upcycled T-shirts and cotton napkins also work, though stretchy knits need a walking foot or stabilizer.

The Basic Construction Method

The process has five stages: cut, sew, turn, topstitch, and finish with a closure. Each takes 10–15 minutes once you have the rhythm.

1. Cut Two Matching Pieces

Use a printable pattern from Apple Green Cottage or Mary Martha Mama. It’s a triangle with a curved or squared neckline. Most free patterns fit babies from about 3 months to 2 years. Cut the pattern on the fold for both front and back pieces. Pin or clip them together with right sides facing.

2. Sew The Perimeter, Leave An Opening

Set your machine to a straight stitch at 2.5 length. Sew around the two long edges and bottom point, staying ¼ inch from the raw edge (⅜ or ½ inch also works — be consistent). Backstitch at both ends. Leave the top edge (neckline) completely open — that 6- to 8-inch opening lets you turn the bib later. Double-check before cutting thread to avoid sewing the whole bib shut.

3. Trim Corners And Turn

Trim the seam allowance at the bottom point and any sharp curves, cutting close to stitches but not through them. Reach through the neck opening and pull the fabric right side out. Use a chopstick or blunt pencil to push the point out fully. Iron flat, rolling the seam slightly to the back.

4. Topstitch Near The Edge

Topstitch around the whole bib, including the open neck edge, about ⅛ inch from the finished edge. This closes the opening, flattens the seam, and gives a crisp look. If the neckline feels stiff, stop topstitching short of the neck curves so it stays softer.

5. Add The Closure

Three options appear across tutorials.

Closure Type Best For Installation Tips
KAM snaps Adjustable fit, stays closed through movement Position two snaps so ends overlap; lets bib grow with baby
Velcro Quick on/off, easy for caregivers Place soft loop side on inside facing baby’s neck; rough hook side outward to avoid scratches
Button + buttonhole Classic look, no special tool needed Test buttonhole placement before cutting; ensure button is too large to be a choking hazard

Test the fit on your baby — the overlap should be snug but not tight, and hardware must never sit directly against the skin.

Common Mistakes And How To Skip Them

Most frustrations come from three places. Skipping the backstitch pops seams open when the bib is yanked. Not trimming the point leaves a blunt tip. Placing Velcro with scratchy side inward rubs baby’s neck raw — always put the soft loop side inside. If using PUL, use clips, not pins, to avoid leaks.

FAQs

FAQs

What size pattern should I use for a newborn?

Most free patterns fit 3 months to 2 years. For a newborn, trace the pattern 15–20 percent smaller or use a dedicated preemie pattern. Neck opening and overlap length matter more than total drop.

Can I use a serger instead of a regular machine?

A serger works for the perimeter seam, but you need a regular machine for topstitching — a serger cannot close the turning opening or sew the ⅛-inch finish line. Many sewers use a serger for speed then switch machines.

How many bibs should I make at once?

Cutting four to six bibs from one fat-quarter bundle or half-yard takes almost the same time as cutting one. Chain-sew perimeters, then turn and topstitch each. Six bibs cover roughly two days of heavy teething drool before laundry.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.