How to Make a Phone Holder? | DIY Stands For Desk, Wall & Bed

Making a phone holder at home is straightforward with cardboard, wire, or wood, though the method depends on your material and where you plan to use it.

The practical route to a homemade phone stand starts with what you already own. A folded plastic card, a stack of binder clips, or a cut cardboard tube all work in seconds, while sturdier builds from wood or fabric take an afternoon. The right choice depends on whether the holder is for a desk, a wall mount, or lying in bed.

The Fastest Options: Binder Clips, Cards, And Cardboard Tubes

When you need a stand right now, three quick builds take under a minute each, and wikiHow documents all of them. A stack of two or three binder clips grips a phone at a comfortable viewing angle. A bent plastic card — fold it in half, then crease a small lip at one edge — props a phone upright on a flat surface. A cut-down cardboard tube from a coffee cup sleeve or paper towel roll does the same job with a little more stability.

These options share one honest limit: they work best on a desk with the phone in portrait mode. None of them hold a tablet, and none survive rough handling. For something more permanent, the builds below last longer.

Building A Sturdy Cardboard Or Popsicle-Stick Stand

Cardboard is the easiest material to shape into a custom holder, and Android Authority’s DIY roundup shows a wall-hanging version that keeps the phone within reach while charging. Trace a template or draw your own, cut it out with an utility knife, then fold along half-cut lines to form the sides and bottom. Reinforce every seam with hot glue or duct tape, and add a top hole for hanging, a middle cutout for the charging cable, and a bottom notch so you can still reach the home button.

Popsicle sticks make a smaller but solid desk stand. One build uses six or seven recycled sticks glued into an “A” shape with a flat platform and an angled support stick behind it; HowStuffWorks recommends hot glue at every joint so the stand does not collapse under the phone’s weight.

Cardboard’s trade-off is durability — it bends and wears quickly. It is the easiest material to work with, but expect to rebuild it eventually.

Wire And Wood Stands For Long-Term Use

A wire stand is the most adjustable DIY option. Start with about 14–18 inches (35–45 cm) of sturdy craft wire, bend it into a three-sided rectangle for the base, then curve the top into a cradle shape that holds the phone at an angle. Small bent wire loops on the bottom corners keep the stand from scratching your desk, per Android Authority’s guide.

A wooden stand is the most durable but requires more tools. Cut a block of wood to size, then cut a groove or slit across the top for the phone to rest in — one guide specifies cutting the groove about halfway through the wood with a table saw, then sanding every edge smooth so it does not snag your phone’s finish.

One build to avoid unless you have the right gear: a PVC pipe stand. Heating and smoothing plastic edges releases fumes, and the source tutorial carries a blunt warning to wear gloves. The payoff is not worth the risk when wire and wood are safer alternatives.

Fabric “Phone Pillow” Holders For Bed Use

If your holder is for watching in bed, a soft fabric pillow beats every rigid material. Cut fabric to a pattern or roughly 5 x 12 inches if you are working freehand, stitch along the sides, turn it inside out, and fill it with microbeads, pellets, or plain rice. Add a ribbon loop at one end and close the top seam. The result is a flexible prop that holds the phone at a comfortable angle without sliding off the mattress.

This design also protects the phone itself — no hard edges to scratch the screen. The one drawback is size: a fabric pillow is bulkier than a rigid stand, so it suits nightstand and bed use better than a desk.

Choosing The Right Material

Material Build Time Best For
Plastic card / binder clips Under a minute Quick desk propping
Cardboard 15–30 minutes Custom wall mounts with charging cutouts
Popsicle sticks 20–40 minutes Lightweight desk stands
Wire 30–60 minutes Adjustable, scratch-free desk stands
Wood 1–2 hours Heavy-duty permanent stands
Fabric / rice fill 45–60 minutes Bed and nightstand viewing

Size every holder to your specific phone, including its case. Case thickness changes the fit dramatically, so measure before you cut. If the holder is for charging, add a cutout for the cable; if it is for speakerphone use, add a hole so the speaker is not muffled. On that note, if a rigid DIY stand feels like too much work, a tested roundup of bed phone holders covers store-bought options that swivel and clamp instead.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.