How to Measure Your Dog for a Custom Harness | Fit First, Buy Second

A custom dog harness is measured by chest girth — wrap a soft tape around the widest part of the rib cage just behind the front legs, then compare that number to the maker’s size chart for the correct fit.

A harness that’s too loose lets a dog slip out during a walk, and one too tight rubs raw spots under the legs. The fix isn’t guessing the size — it’s taking one reliable chest measurement and using the brand’s own chart. Here’s the exact method, the common mistakes to skip, and how to know when you’ve nailed the fit.

The One Measurement That Matters Most

Chest girth is the single number every harness maker needs. Measure at the widest part of the rib cage, which is typically right behind the front legs when the dog stands naturally on all fours on a flat surface. Use a soft cloth tape measure — or a piece of string plus a ruler if that’s all you have — and keep the tape snug without digging in. The Orvis guide recommends leaving enough room for two fingers under the tape for comfort, though some brands adjust this by 1–2 cm depending on their design. Take the measurement three times to reduce error and use the average that lands on the maker’s chart. Record in the unit the manufacturer uses (centimeters are common for custom work).

When You Need More Than Just Girth

Some harness styles — especially step-in, over-the-head, and fully custom designs — also need the neck circumference measured at its base. For deep-chested breeds, add the distance from the base of the neck to the start of the rib cage so the straps don’t end up sitting in the armpit. Use the same soft tape and standing posture. The Chewy education guide emphasizes keeping the tape level and untwisted around the body for every measurement you take.

Common Measuring Mistakes to Avoid

Most fitting problems come from one of these errors:

  • Measuring the dog while sitting, lying down, or wiggling — the chest compresses and the girth reads smaller than the real number.
  • Wrapping the tape too close to the armpits instead of the widest chest point, which makes the harness ride up.
  • Pulling the tape tight rather than snug, which produces a size that’s too small and restricts movement.
  • Ignoring the manufacturer’s own size chart — a number that fits one brand can be off by a full size on another.
  • Forgetting to account for thick fur or heavy coats, which can add an inch or more and cause a snug harness to become tight.

When a dog falls between two sizes on a chart, the safer general rule is to size up and tighten the adjustment straps down rather than squeeze into the smaller size that might bind. If you’re looking for a new harness and want something that also looks sharp for daily walks, check out our roundup of durable and stylish dog accessories that fit the same careful measurement approach.

How to Tell the Fit Is Right

After putting the harness on, check these signs: the dog should move shoulders and front legs freely with no rubbing or bunching at the skin. The strap that wraps the chest should sit behind the front legs, not jammed into the armpit. The most common comfort check is the two-finger test — you should be able to slide two flat fingers under any strap — but the brand’s own fit guidance takes priority if it specifies a different allowance. Adjust the straps evenly on both sides, then walk the dog a few steps and look for any slippage or chafing spots before a long outing. A proper fit for a custom harness eliminates the guesswork and keeps the dog secure and comfortable every time.

FAQs

Should I measure my dog standing or sitting?

Always measure with your dog standing on all fours on a hard, flat surface. The chest is at its natural widest point in this stance, and the tape can wrap level around the body without folds or compression from a sitting position.

Can I use a metal tape measure for chest girth?

A soft cloth tape is best because it conforms to the dog’s body shape. If you only have a metal or rigid tape, use a string to wrap the chest first, mark the overlap, and then lay the string flat against a ruler or the tape to read the length.

What if the measurement lands right between two sizes?

Size up to the larger option when you’re between sizes, then tighten the adjustment straps. A slightly larger harness can be snugged down, but a too-small harness will restrict movement and can rub the skin raw under the legs.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.