How to Remove Old Kitchen Sink Faucet | Done in 30 Minutes

Removing an old kitchen sink faucet requires shutting off the water, disconnecting the supply lines, and unscrewing the mounting nuts from below the sink.

Plumbing projects have a way of turning a Saturday morning into an afternoon. A faucet that’s been holding steady for fifteen years doesn’t want to let go, and the tight space under the sink makes every turn of the wrench feel harder than it should. Getting that old fixture off without damaging the sink or the supply pipes is straightforward if you’ve got the right tools and the right order of steps. Below is the exact sequence that works for standard deck-mounted kitchen faucets found in most US homes.

What You’ll Need Before Starting

The difference between a twenty-minute removal and a two-hour wrestling match is having the right tools under the sink before you start. A basin wrench is the critical tool—its long handle and pivoting jaw reach mounting nuts in the tight gap behind the sink bowl. An adjustable wrench handles the supply line nuts. Keep a utility knife or plastic putty knife, safety glasses, a flashlight, a towel, penetrating oil (like WD-40 or Liquid Wrench), and a small plastic bucket on hand. A screwdriver helps with hose clamps or clips on pull-down sprayer models.

Step-by-Step: How to Remove an Old Kitchen Faucet

1. Turn Off the Water and Drain the Lines

Clear everything from under the sink. Locate the hot and cold shut-off valves—usually two chrome or plastic knobs on the pipes coming out of the wall or cabinet floor. Turn both clockwise until they stop. If the under-sink valves are missing or won’t turn, shut off the home’s main water supply. Block the sink drain with a cloth to catch dropped parts. Open the faucet handle fully to release water pressure and let the remaining water drain into the sink. If the faucet has a sprayer, pull the sprayer head down to drain that line too.

2. Disconnect the Supply Lines

Use the adjustable wrench to loosen the threaded nut connecting the hot supply line (left side) to the shut-off valve, turning counterclockwise. Stabilize the water pipe with your other hand while loosening to avoid stressing the valve. Repeat for the cold supply line (right side). If the faucet has a separate sprayer hose, use the basin wrench to reach the diverter nut where the sprayer hose connects at the faucet base. Have the towel and bucket ready—a small amount of water will spill from the disconnected lines.

3. Remove the Mounting Nuts

This is the step where old faucets fight back. Look under the sink for the large mounting nut (or two nuts on a deck plate) that holds the faucet base to the sink deck. Use the basin wrench—set the jaw to grip the nut, then turn counterclockwise from the handle’s end. If the nut is stuck, spray penetrating oil around the threads, wait 15 minutes, and try again. For stubborn mineral deposits, white vinegar applied with a rag can help. Avoid using excessive force with a standard wrench that could snap the faucet tailpiece or crack the sink.

If the nut still won’t budge: alternate approaches include gentle heat from a hair dryer or heat gun (careful with plastic parts), careful hammering with a screwdriver on the nut’s edge, or (for truly seized bolts) cutting the bolt with a hacksaw blade or oscillating saw. For broken screws, use vice grips or break the faucet sideways with a hammer.

4. Lift the Faucet and Clean the Surface

Once all mounting nuts are off, grip the faucet body and pull straight up. If it sticks, run the plastic putty knife between the faucet base and the sink deck to break any old caulk or plumber’s putty seal. Never use a metal putty knife or screwdriver—one slip leaves a permanent scratch in the sink finish. With the faucet removed, scrape away old putty, caulk, and debris from the sink deck using the putty knife and an approved cleaner.

If you’re replacing the faucet with something fresh rather than classic, our roundup of antique-style kitchen faucets covers the best options that blend old character with modern water-saving cartridges.

Common Mistakes That Cost Time

Three errors turn a simple removal into a repair call. Forcing stuck nuts without penetrating oil or heat crushes brass threads or cracks the sink. Skipping the drain block sends a small nut or screw straight into the garbage disposal or P-trap. Using metal tools to break the caulk seal leaves scratches in stainless steel or enamel that show every water spot. Wear safety glasses throughout—old mineral deposits and rust flakes fall when you least expect them.

Post-Removal: What to Do Before Installing the New Faucet

Before setting the new faucet in place, inspect the sink deck for damage and clean every bit of old sealant. When the new faucet is installed, turn the shut-off valves on slowly and check every connection for drips. Tighten any leaky nut gently—over-tightening is the most common cause of cracked supply line nuts. Remove the new faucet’s aerator, run full-blast hot and cold water for one minute to flush out debris, then reinstall the aerator. Delta Faucet’s official removal video shows the same basin wrench technique used by experienced plumbers.

FAQs

Can I remove a kitchen faucet without a basin wrench?

Yes, if you can reach the mounting nuts with a standard adjustable wrench. Some sink basins have enough clearance for a short wrench on the side of the nut. A basin wrench is still the tool for tight spaces behind deep sinks.

What if my shut-off valves won’t turn?

If the under-sink valves are stuck or seized, shut off the home’s main water supply instead. This is common in older homes where quarter-turn valves haven’t been exercised in years. Replace the stuck valves after the faucet job is done.

How do I remove a faucet with broken mounting nuts?

Use a hacksaw blade to cut through the nut or bolt below the sink deck. For extremely corroded nuts, an oscillating multi-tool with a metal-cutting blade works well.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.