How to Replace a Valve Cover Gasket | Stop The Leak The Right Way

A valve cover gasket replacement requires clean sealing surfaces, a dry gasket install, and fastener torque to the engine’s exact specification.

That burning-oil smell at a stoplight means oil is escaping past the valve cover gasket. The process for how to replace a valve cover gasket involves three non-negotiable steps: clean the mating surfaces, install the new gasket dry unless the manual requires sealant, and torque the fasteners to the engine’s exact number. With basic tools and a torque wrench, this is a weekend job that stops the leak for good.

Can I Just Tighten The Bolts Instead Of Replacing The Gasket?

If the gasket has not hardened or torn and the leak developed slowly, tightening the valve cover bolts to the manufacturer’s torque spec may stop it. Use a torque wrench — never guess by feel — and torque each fastener in the correct sequence. If the leak continues after torquing, the gasket has failed and replacement is the only lasting fix. Overtightening will crush the gasket or crack a plastic cover, so the spec is non-negotiable.

Replacing A Valve Cover Gasket: The Installation Sequence That Works

Start with a fully cooled engine. Remove any components blocking valve cover access: the decorative engine cover, throttle cables, spark plug brackets, PCV hoses, ignition coils, and intake parts vary by vehicle but must come off. Disconnect coil connectors and remove coil bolts if they sit above the cover.

Remove the valve cover bolts in the factory sequence and lift the cover off. If it sticks, tap it gently with a rubber mallet or carefully pry it loose — do not let old gasket fragments or debris drop into the engine. Remove the old gasket and any tube seals or grommets included in the replacement kit.

Clean both sealing surfaces — the valve cover groove and the cylinder head mating face — with a towel and carburetor cleaner until no residue remains. Fel-Pro’s official guidance states that its valve cover gaskets are installed clean and dry. Apply silicone or RTV only where the service manual explicitly requires it; using sealant where it is not specified can cause the gasket to displace and leak. If sealant is required, remove all oil from the surfaces and let it cure per the instructions before starting the engine.

Install the new gasket in the cover’s groove. For Fel-Pro PermaDry press-in-place gaskets, press straight down in short sections rather than sliding the gasket along the groove, which can leave leftover material and cause leaks. Replace any spark plug tube seals or grommets that came with the kit.

Reinstall the cover and torque each fastener to the manufacturer’s specification in the correct sequence. If no sequence is provided, start from the center and work outward, alternating fasteners. For engine families with known sealing challenges — like the 7.3 Powerstroke — a dedicated gasket set improves results; check our roundup of the best Powerstroke gaskets for tested options. Never overtighten: a torque wrench set to the spec prevents the distortion that causes repeat leaks.

Common Valve Cover Gasket Mistakes

Mistake Result How To Avoid
Overtightening bolts Distorted gasket or cracked plastic cover Use a torque wrench set to the engine’s spec
Using RTV without a spec Gasket displaces, causing new leaks Apply sealant only where the manual requires it
Failing to clean surfaces thoroughly Oil seeps through old gasket residue Scrub both mating faces with carb cleaner and a lint-free towel
Skipping new grommets or tube seals Oil leaks around bolt holes or spark plug wells Replace every seal included in the gasket kit
Reusing a warped or cracked plastic cover New gasket cannot seal evenly Inspect the cover for cracks and warping; replace it if damaged

Fel-Pro’s valve cover gasket installation guide reinforces that cleaning and correct torque are the two steps that separate a one-and-done repair from a return trip.

FAQs

How much does a valve cover gasket replacement cost?

A valve cover gasket kit for most cars costs between $15 and $50 for the gasket and seals. Labor for a shop install typically runs $150–$400 depending on how much must be removed for access. Doing it yourself saves the labor cost entirely.

Can I drive with a leaking valve cover gasket?

You can drive short distances with a minor seeping leak, but a steady drip should be addressed promptly. Oil on the exhaust manifold produces smoke and a burning smell, and in some cases it can damage spark plug tube seals or contaminate the ignition system over time.

How long does a valve cover gasket replacement take?

On most inline engines the job takes about one to two hours for a first-timer. V-configuration engines need separate gaskets for each bank and can take three to four hours because the intake manifold often must be removed for access to the rear valve cover.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.