How to Use a Hay Spear | Lift Bales The Right Way

Using a hay spear safely requires driving the implement fully into the bale’s center before lifting, keeping the load low during transport, and never allowing anyone near the raised load.

Whether you’re feeding livestock or stacking winter stores, a hay spear turns a tractor or skid steer into a one-person bale-moving machine. The process is straightforward, but skipping steps can bend tines, tear net wrap, or tip the machine. What follows is the safe, field-tested sequence from pre-check to set-down — no more than you need, nothing left out.

Pre-Operation Checks and Attachment

Before touching a bale, inspect the spear for loose bolts, cracked welds, bent tines, or damaged locking pins. One cracked weld at the mounting plate can drop a half-ton bale the moment you lift. Clean dirt and debris off the mounting surfaces so the quick-attach or 3-point hitch locks seat fully — a partial lock can release under load.

On a 3-point hitch, connect the top link and lower arms, then secure the locking pins. For loader-mounted or skid-steer spears, make sure the attachment plate engages completely and the spring-loaded pins click into their locked position. If your spear has hydraulic lines (common with grapple-style units), check for leaks or loose fittings.

Approaching and Spearing the Bale

Align the spear horizontally with the bale’s center. For round bales, aim the spear point at center height or slightly above — this helps the two lower spikes (on models like the Great Plains BS10 and BSE10) enter fully. Approach at a slow, steady speed and drive the spear straight into the bale until it is completely seated. The point should emerge from the far side at least a few inches before you attempt any lift.

Never scoop a bale with the tines. The spear must penetrate fully through the bale from the start. If the lower spikes don’t enter on the first attempt, raise the spear slightly and try again until all tines engage. Bales that are tightly wrapped or frozen can resist penetration — this is the moment to reposition, not to force it.

When you’re ready for a new spear, see our tested roundup of the best 3-point hay spear options for compact tractors.

Lifting, Transporting, and Setting Down

Raise the bale only enough to clear the ground — usually 8–12 inches. Keeping the load low preserves stability and your forward visibility, which large round bales block almost completely. On slopes or uneven ground, the bale’s weight shifts your machine’s center of gravity; low and slow is the only safe speed. Avoid abrupt turns or sudden stops, which can shift the bale on the tines or damage the wrap.

At the destination, lower the bale gradually until it rests on the ground. Reverse the tractor or loader slightly to slide the spear out cleanly. Never try to back out while the bale is still suspended — the sudden release can cause the spear to spring up or the bale to roll back onto the machine.

Loader-Mounted vs. 3-Point Hitch Differences

A loader-mounted spear can be tilted with the bucket curl, which is useful for centering on misshapen bales. A 3-point-hitch spear has less tilt adjustment; you rely on the top-link length for the approach angle. For 3-point spears, set the top link so the lower tines are level or slightly pointed up when the spear is at working height. Skid-steer spears operate similarly to loader-mounted units, but always confirm the attachment plate locks are fully seated — these take more vibration than tractor mounts.

Step Key Action Common Mistake to Avoid
Pre-check Inspect tines, welds, pins, and mounting Ignoring hairline cracks or loose bolts
Attach Secure all locking pins; clean debris from mount Partial lock engagement that releases under load
Approach Align spear with bale center; drive in fully Scooping instead of spearing straight through
Lift Raise bale just enough to clear ground Lifting high, which reduces stability and visibility
Transport Drive slowly; avoid abrupt turns or stops Speeding or sharp turns that shift the load
Set down Lower gently; reverse to slide spear out Backing out while bale is still suspended
Maintenance Clean after use; lubricate pivots; inspect Storing a dirty, corroded spear that will seize later

FAQs

Can you use a hay spear on a loader without a 3-point hitch?

Yes. Loader-mounted bale spears attach directly to the loader’s quick-attach plate and are common on compact tractors and skid steers. They offer tilt control through the loader’s lift and curl functions, which helps center the spear on the bale.

How do you know if a bale spear is rated for your bale size?

Check the manufacturer’s rated capacity against your bale’s typical weight. A 4-foot round bale of dry hay might weigh 500–700 pounds, while a 6-foot bale of wet silage can exceed 1,500 pounds. Never exceed the spear’s design limit — overloading bends tines or breaks the mount.

Why does my bale keep slipping off the spear during transport?

The spear is likely not inserted fully, or the approach angle was off. The tines must exit the far side of the bale before lifting. If the spear enters too low in a round bale, the bale can tip forward on the tines. Always aim at or slightly above center.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.