A rivet gun sets a blind rivet by pulling its mandrel until it snaps, expanding the rivet body to clamp two or more pieces of material together.
A rivet gun looks intimidating, but the process boils down to five steps: pick the right rivet, drill a clean hole, load the rivet, pull the trigger (or squeeze the handles), and check that the joint is tight. The whole operation takes about ten seconds per rivet once you have the setup right. Whether you are patching a gutter, repairing a trailer, or building a project from scratch, the same fundamentals apply.
Choosing the Right Rivet for Your Material
The rivet must be the correct diameter for the hole and long enough to pass through the total thickness of both pieces, with enough leftover to form the blind-side upset. Hand riveters usually ship with three or four interchangeable nosepieces that must match the rivet diameter, so check that the nozzle sits snugly before you load anything.
If the rivet is too short, it cannot form a secure blind head. If it is too long, it may bulge or tear rather than clamp the sheets together. When in doubt, measure the stack thickness and match it to a rivet grip range published by the manufacturer.
Step-by-Step: Using a Hand Rivet Gun
Clamp and align the workpieces tightly before you drill—any gap between the sheets is the most common reason a rivet sets loose. Remove burrs and shavings from the hole so the rivet head seats flat against the surface.
- Set the nosepiece to the rivet diameter. Swap the nozzle until the mandrel slides in and fits without wobble.
- Load the rivet. Insert the mandrel into the nosepiece until it seats snugly. The rivet body now extends from the front of the tool.
- Place the rivet through the hole. Push the rivet body into the pre-drilled hole until the head contacts the near-side material.
- Hold the gun square to the work. Press firm pressure against the rivet head before you actuate the tool. A 90-degree angle is critical; any tilt will set the rivet crooked and loosen the joint.
- Squeeze the handles (or pull the trigger) until the mandrel snaps. The mandrel will break off with a distinctive “pop.”
- Discard the spent mandrel. It is a sharp metal fragment; dispose of it safely.
- Inspect the set rivet. The head should sit flat and tight against the near surface, and the blind side should be expanded fully with no looseness or tilt. If you see a gap between the two sheets, the rivet expanded between them rather than behind them—that joint will fail.
If you are working on a frequent or large project and want a tool that handles 1/4-inch rivets and heavier materials without fatigue, you can browse our roundup of the best 1/4-inch rivet guns tested for grip, leverage, and durability.
Pneumatic Rivet Guns: What Changes
A pneumatic rivet gun works the same way but replaces manual handle force with compressed air. Match the air pressure to the tool manufacturer’s recommendation—guessing can damage the rivet or the gun. The pneumatic models typically eject spent mandrels automatically, which speeds up repetition. The same rules apply: square to the work, firm pressure before triggering, and a short burst instead of a prolonged trigger hold. Always keep your hands clear of the tool’s moving parts, and never trigger the gun unless it is pressed hard against the rivet head.
Common Mistakes That Ruin a Rivet Joint
Most rivet failures trace back to one of four errors. The wrong rivet diameter or length leaves a joint that pulls apart under load. An unclamped workpiece lets the sheets separate while the rivet sets, so the expansion fills the air gap instead of clamping the material. A misaligned drill angle or a hole that was not deburred prevents the rivet head from seating flush. And a gun held at anything other than 90 degrees produces a tilted rivet with uneven clamping force. All of these are avoidable with a moment of inspection before you pull the trigger.
The official documentation for blind rivet tools from manufacturers like Rapid confirms the same procedures: press firmly, keep the tool square, and let the mandrel snap cleanly.
FAQs
Can I reuse a rivet after pulling it out?
No. A set rivet is deformed permanently during installation. The only way to remove it is to drill out the rivet head with a bit slightly larger than the mandrel hole, then punch the remaining body through.
Do I need a special drill bit for rivet holes?
Standard high-speed steel (HSS) drill bits work fine for most metals. The important thing is the diameter—match the bit to the rivet body size. A 1/8-inch rivet typically fits a #30 drill hole, while other sizes follow standard drill charts.
Why does my rivet spin after I set it?
A spinning rivet means the mandrel broke before the rivet body expanded enough to grip the hole wall. The cause is usually a loose nosepiece or insufficient handle pressure before actuation. Re-drill the joint and set a new rivet with a snug nozzle and firm downward pressure.
References & Sources
- Rapid. “How to use a rivet gun.” Step-by-step guide covering hand and pneumatic rivet procedures, nozzle selection, and common mistakes.
- Brighthub Engineering. “Basic Skills for Metal Riveting.” Technical notes on rivet length rules, drill sizing, and proper setting technique for blind rivets.
