Square Tubing Size Chart | Sizes, Gauges & Weight Per Foot

A tubing size reference table maps outside dimensions to wall thickness and weight per foot, helping you select the right material for your project.

A fabrication project lives or dies on picking the right tube, and a square tubing size chart turns guesswork into a measured choice. It maps outside dimensions to wall thickness and weight per foot — the three numbers that determine whether a tube fits, supports the load, and ships at the right cost. There is no single universal chart because sizes vary by material type, standard, and supplier. But every chart follows the same basic layout: once you know how to read one, you can work with any of them.

What Does A Square Tubing Size Chart Include?

A square tubing size chart lists three data points: the outside dimension (the square width), the wall thickness (given as a gauge number or a decimal inch value), and the weight per foot. The outside dimension is the full width from outer edge to outer edge, not the inner opening. Wall thickness determines load capacity — thicker walls are stronger but heavier and more expensive. Weight per foot is calculated from size and wall thickness and matters for shipping costs and structural load calculations.

For US buyers, charts typically show sizes in inches with gauge options from 22 gauge (thinnest) up through 13 gauge (thickest). Metric charts use millimeters and kilograms per meter and are not directly interchangeable without conversion and tolerance checks. The Metals USA square mechanical tubing chart, for example, includes entries from 3/8 x 3/8 inch up through 1 x 1 inch, each paired with its gauge and weight per foot. Suppliers like Service Steel Warehouse and Coremark Metals publish their own versions, but the layout stays consistent: outside dimension, wall thickness gauge, and weight per foot, organized by size first.

How Do You Read A Square Tubing Size Chart?

Reading a square tubing size chart takes three steps: find the outside dimension you need, pick the wall thickness that matches your load requirements, and verify the weight per foot for shipping, handling, and material cost estimates. Start with the tube’s outside dimension — the width of the square — measured in inches for US charts. Common sizes run from 3/8 inch up to 1 inch and beyond. Once you have found that row, look across to the wall thickness column, which will show either a gauge number such as 16 ga or a decimal like 0.065 in. Thicker walls handle heavier loads but add weight and cost.

The weight per foot is the third column and is essential for calculating total material weight. Multiply the per-foot weight by the total length to get the overall weight. Here is a sample of representative sizes from supplier charts:

Outside Dimension Gauge Weight per Foot
3/8″ x 3/8″ 22 ga 0.132 lb
1/2″ x 1/2″ 16 ga 0.385 lb
5/8″ x 5/8″ 18 ga 0.384 lb
7/8″ x 7/8″ 14 ga 0.894 lb
1″ x 1″ 19 ga 0.547 lb

For common sizes up to 1 inch, the chart covers most needs, but for larger dimensions such as 1 1/4 inch, our tested roundup of the best 1 1/4 square tubing options helps you compare rated products side by side. When using the chart, always confirm the tube’s material grade — for structural applications, ASTM A500 Grades B, C, and D are the common standards. The chart gives you size and weight, but the grade determines the tube’s strength and suitability for load-bearing use.

Common Mistakes When Using A Square Tubing Size Chart

The most frequent error is confusing square tubing with square bar or pipe. Square tubing charts are based on outside dimension and wall thickness, while pipe uses a nominal schedule system — they are not interchangeable references. Square bar is solid, not hollow, so its weight and strength characteristics are completely different. Gauge numbers also trip up buyers: the same gauge number can correspond to different decimal thicknesses depending on the supplier and material, so the decimal wall value is the safer reference for precision work. Some suppliers list wall thickness as a decimal rather than a gauge, which eliminates the variability issue entirely — if you see both, use the decimal value.

Size alone does not determine strength. Wall thickness, material grade such as ASTM A500, and specific load conditions all matter. For load-bearing or code-related projects, the chart is a starting reference and not a substitute for engineering verification. Use it to narrow your options, then confirm your final choice against the applicable standard.

FAQs

Is gauge the same across all suppliers?

No. The same gauge number can map to slightly different decimal thicknesses depending on the supplier and material type. When precision matters, use the decimal wall thickness listed on the chart rather than relying on the gauge number alone.

Can I use a square tubing size chart for pipe?

No. Square tubing charts use outside dimension and wall thickness, while pipe sizing uses nominal pipe schedule — a different reference system that is not interchangeable with tubing measurements.

Does a larger size always mean stronger tubing?

Not by itself. Strength depends on wall thickness, material grade such as ASTM A500 Grade B or C, and how the tube is loaded. A larger outside dimension with a thin wall can be weaker than a smaller tube with a thick wall.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.