What CFM Range Hood Do I Need? | Size Right, Vent Better

Most U.S. kitchens need a range hood between 300 and 1,200 CFM, with the exact rating set by cooktop type, burner output, and room size.

Figuring out what CFM range hood you need starts with three separate checks—cooktop BTU output, cooktop width, and kitchen volume—and using the largest result as your baseline. Gas cooking demands more airflow than electric or induction, and ductwork losses can push the final number higher. Here is how each method works and how to combine them for the right call.

How Many CFM Does Your Kitchen Actually Need?

Three independent sizing rules exist for residential range hoods, and the right approach is to run all three, then go with the highest number. No single U.S. standard covers every kitchen, so these heuristics work together.

BTU output method (gas only). Add the BTU rating of every burner on your cooktop, then divide by 100. A 40,000 BTU gas cooktop needs at least 400 CFM. This is the most direct measure for gas cooking because it matches airflow to actual heat and combustion output.

Width method (all cooktops). For wall-mounted or under-cabinet hoods, plan on 100 CFM per linear foot of cooktop width. A 36-inch cooktop needs about 300 CFM. Island hoods need roughly 150 CFM per linear foot because the open sides let smoke drift more easily.

Kitchen volume method. Measure your kitchen’s length, width, and height in feet, multiply them, then divide by 4. That gives the CFM needed to cycle the room’s air about 15 times per hour. A 12 × 15 × 8-foot kitchen (1,440 cubic feet) works out to 360 CFM.

Method How To Calculate Example Result
BTU (gas cooktop) Total BTU ÷ 100 40,000 BTU → 400 CFM
Width (wall hood) Width in ft × 100 36-inch cooktop → 300 CFM
Width (island hood) Width in ft × 150 36-inch cooktop → 450 CFM
Kitchen volume (L × W × H) ÷ 4 12×15×8 ft → 360 CFM
Duct elbows +25 CFM each 2 elbows → +50 CFM
Duct length +1 CFM per foot 10 ft → +10 CFM
Roof cap +40 CFM +40 CFM

How To Find Your Minimum CFM Step By Step

Once you have baselines from the three methods above, follow these steps to settle on a final CFM target.

1. Pick the highest baseline. Compare the BTU, width, and volume results. If your gas cooktop gives 400 CFM but the kitchen volume only needs 300 CFM, start with 400.

2. Add ductwork losses. Per Broan-NuTone’s CFM guide, every 90-degree elbow adds about 25 CFM of resistance, every foot of straight duct adds about 1 CFM, and a roof cap adds roughly 40 CFM. A typical run with two elbows, 10 feet of duct, and a roof cap needs about 90 extra CFM above the baseline.

3. Factor in cooking style. Heavy frying, wok cooking, or high-BTU commercial-style ranges push the need toward 900 CFM or more. Light to moderate cooking on a standard gas range often does fine at 400–600 CFM.

4. Check make-up air requirements. Local building codes may require a make-up air system for hoods rated above 600–900 CFM, because high-powered exhaust can depressurize a home and back-draft combustion appliances. Verify your local code before buying.

Once you know your target CFM rating, browse tested range hoods at that rating to compare noise levels, duct sizes, and mounting options that match your kitchen.

Common Range Hood Sizing Mistakes

Even with the right math, a few recurring errors lead to poor performance.

  • Using only room volume. For gas cooktops, the BTU method should dominate because it accounts for combustion gases that volume alone doesn’t capture.
  • Buying a hood narrower than the cooktop. Whirlpool recommends a hood at least as wide as the cooktop, ideally 3 inches wider on each side, to capture rising smoke before it spreads.
  • Ignoring duct losses. A hood rated at 600 CFM may deliver only 500 CFM after elbows and a long duct run. Add the losses before choosing a model.
  • Assuming bigger is always better. An oversized hood pulls more air than necessary, creating noise, heating or cooling loss, and potential make-up air problems. Size to your actual needs.
  • Treating one rule of thumb as law. Multiple heuristics exist; the right approach compares all three methods and uses the highest number.

FAQs

Is 300 CFM enough for a gas range?

300 CFM is a practical minimum for many standard residential gas cooktops with total burner output under 30,000 BTU. For heavier cooking or higher BTU burners, 400–600 CFM delivers noticeably better smoke and odor capture.

How many CFM do I need for a 36-inch gas cooktop?

The width method suggests about 300 CFM, but the BTU method often yields a higher number, and adding duct losses pushes the final target higher.

Does duct size affect CFM requirements?

Yes. Hoods rated at 400 CFM and under can use a minimum 4-inch duct. Higher CFM hoods require larger ductwork—6 inches or more—to avoid excessive noise and restricted airflow. Undersized ducting strangles performance regardless of the hood’s rating.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.