What Size Wire for 35 Amp Breaker | NEC Code Requirements

For standard branch circuits, an 8 AWG copper wire is the minimum size the NEC requires for a 35-amp breaker, though special exceptions apply for AC equipment.

Installing a 35-amp breaker with the wrong wire size creates a serious fire hazard, so knowing what size wire for a 35 amp breaker is required by code matters before you start the job. The National Electrical Code (NEC 2023) sets clear rules, and the short answer is 8 AWG copper for general circuits, with a narrow exception for air conditioning and refrigeration equipment covered under NEC 440.6.

Minimum Wire Size for a 35 Amp Breaker

The NEC requires 8 AWG copper as the minimum wire size for a 35-amp breaker on standard branch circuits. NEC Section 240.4(D) explicitly limits 10 AWG copper to a maximum 30-amp breaker, so running 10 AWG on a 35-amp breaker for general loads violates code and risks overheating. Eight AWG copper carries adequate current at all common insulation temperatures — 40 amps at 60°C (NM-B cable), 50 amps at 75°C (THWN), and 55 amps at 90°C (THWN-2) — confirmed by NEC Table 310.16 ampacity charts. For aluminum wiring, 8 AWG is also the minimum, and it requires anti-oxidant compound with terminals rated for aluminum connections.

Parameter Specification
Minimum copper wire 8 AWG
Minimum aluminum wire 8 AWG
Max breaker for 10 AWG copper 30 A (NEC 240.4(D))
Exception for 10 AWG AC/Refrigeration if nameplate permits (NEC 440.6)
8 AWG ampacity (90°C, THWN-2) 55 A
8 AWG ampacity (75°C, THWN) 50 A
8 AWG ampacity (60°C, NM-B) 40 A
Continuous load limit on 35 A breaker 28 A (80% rule)

When Is 10 AWG Wire Permitted?

NEC 440.6 creates a limited exception for HVAC and refrigeration equipment. If the manufacturer’s nameplate explicitly specifies 10 AWG copper with a 35-amp overcurrent protection device, that setup is code-compliant. This exception exists because compressors and motors draw peak current only briefly during startup, reducing continuous-load risk. You must keep the manufacturer’s documentation on hand, and your local inspector may require explicit sign-off. This exception does not apply to general-purpose outlets, lighting circuits, or any branch circuit feeding standard receptacles — those must follow the 8 AWG rule under 240.4(D).

How to Choose the Right Wire Size

Start by classifying the load. A continuous load — one running three hours or more — must be calculated at 125% of its actual draw per NEC 210.19(A)(1). A 24-amp continuous load times 1.25 equals 30 amps, which works with 10 AWG wire, but the breaker cannot exceed 30 amps under 240.4(D). So with a 35-amp breaker, the maximum safe continuous draw is 28 amps (80% of 35). For non-continuous loads, 8 AWG copper covers the full 35 amps without issue.

Check voltage drop on longer runs. The NEC recommends keeping branch-circuit voltage drop under 3%. For runs exceeding 100 feet, 8 AWG may drop voltage enough to affect equipment performance, and upsizing to 6 AWG is a practical solution. Also verify terminal ratings — your breaker and connection points must be rated for the wire’s insulation temperature to legally use higher ampacity values. If terminals are only 60°C-rated, 8 AWG is still safe at 40 amps, which comfortably covers the 35-amp breaker. When you’re ready to choose a breaker that pairs correctly with 8 AWG wire, our roundup of the best 35-amp breakers covers reliable models from Siemens, Square D, and GE with current specs.

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.