A drill bit works by using its cone-shaped tip and sharp cutting lips to shear material away while spiral flutes channel the waste chips up and out of the hole.
Understanding how a drill bit actually works explains why certain bits cut smoothly while others grab, overheat, or snap. Every drill bit converts the drill’s rotational force into a precise shearing action: the pointed tip centers on the mark, the cutting lips peel material away along a shear plane, and the flutes shuttle debris out so the cut stays clean and cool. Choose the right bit for the material, and you get a perfect hole. Choose wrong, and the bit fights you the whole way.
The Four Parts That Make a Bit Cut
A drill bit has four basic components: the diameter determines hole size, the shank gets clamped in the chuck, the flutes clear waste, and the point does the cutting. The shank varies between round and hex shapes — impact drivers need hex shanks with quick-connect ends, while standard drills use round shanks. The flutes don’t cut; they’re spiral channels that pull chips upward, preventing clogging and overheating. At the tip, the cone-shaped point features a spur that centers the bit and a cutting lip that does the real work — the surface behind the lip drops away slightly to create relief, so the bit feeds without rubbing.
How the Shearing Action Works
The cutting lip compresses material in front of it until the material fails along a shear plane, forming a chip. That chip rides up the rake face — the front surface of the flute — and exits. The chisel point at the very center helps position the bit, but it doesn’t cut; it pushes material aside, which is why drilling metal often starts with a center punch. On a high-speed steel (HSS) twist bit — the most common type — this action works well in wood, plastic, and soft metals. For harder materials, the bit material and point angle matter just as much.
If you’re looking at specific bits, our tested guide to the best drill bit sets for home and shop use covers top performers across materials and price ranges.
Point Angles and Bit Materials: What to Use Where
The most common point angle is 118 degrees — it cuts aggressively and works best in soft materials like wood and plastic. The 135-degree angle is less aggressive, designed for harder materials like metal and masonry; it reduces wandering or grabbing. Bit materials also dictate performance: standard HSS bits handle most homeowner jobs, cobalt and carbide bits hold up to heat in heavy-duty metal drilling, and diamond or tungsten carbide bits with spear-shaped tips are required for glass and ceramics to prevent cracking.
Specialty bit types exist for specific jobs. A brad-point bit gives a perfectly clean hole in wood without tear-out. A step bit lets you drill multiple hole sizes with one cone-shaped bit. Spade bits bore large holes quickly in wood, and auger bits with screw points and deep flutes remove wood chips fast, ideal for deep framing or timber work.
How to Install and Use a Bit Correctly
Installing a bit safely avoids broken bits and ruined workpieces. Always unplug or remove the battery first. Open the chuck jaws by turning counterclockwise, insert the bit until it bottoms out, then pull it back about 1/16 inch — this gap prevents bottoming out under load. Tighten the chuck clockwise until it won’t turn further.
For wood drilling with a twist bit: mark the spot, set the drill to its highest speed, and create a starter dent. Start slow, increase speed as the bit engages, and maintain steady pressure straight through. Reverse the drill to back it out if it binds. For metal drilling: switch to lowest speed, apply one or two drops of machine oil as lubricant, and use a center punch first so the bit doesn’t slide. Start with heavy pressure at low speed and feather the trigger to increase speed while keeping steady force. Add oil during the cut to prevent heat buildup — overheating is the fastest way to ruin a bit.
For pilot holes before screws: match the bit diameter to the screw’s solid shank (not threads). The fastest way to check is holding the bit against the screw — threads should be visible, but the shank itself should match the bit width.
FAQs
Can you sharpen a dull drill bit?
Yes — dull bits can be resharpened using a bench grinder or a dedicated bit sharpener like Drill Doctor. The key is maintaining the original point angle (118° or 135°). A correctly sharpened bit cuts like new; a poorly sharpened one will wander or overheat.
Why does my drill bit keep getting stuck?
Binding usually happens when chips aren’t clearing — pull the bit out periodically while drilling deep holes. Using the wrong speed for the material also causes binding: slow speeds for metal, high speeds for wood. Lubrication prevents sticking in metal.
What does the number on the side of a drill bit mean?
That number is the bit diameter in fractions of an inch (e.g., 1/4) or in millimeters. Wire-gauge numbers (like #10) are also common. A numbered bit’s diameter must be looked up on a drill bit size chart — the number itself isn’t the size in inches.
References & Sources
- Wikipedia. “Drill bit.” Comprehensive overview of drill bit types, anatomy, and historical development.
- ScienceDirect. “Drill bit.” Technical breakdown of cutting mechanics and material science behind drill bits.
- Fastenal. “Drill Bit Selection Guide.” Practical reference for bit materials, point angles, and application matching.
