How to Measure Basement Windows? | Rough Opening, Egress Rules

Measure the rough opening, not the old window, taking width at three points and height at three points, then use the smallest figures.

Basement window replacements fail most often because someone measured the old sash or included the trim. The number that matters is the rough opening — the bare framed hole in the wall. Grab a steel tape measure and follow the three-point method both directions so the replacement fits the gap, not the guess.

Measure Width And Height At Three Points Each

Work from inside the home with the old window still in place. Measure the width at the top, middle, and bottom of the opening, then record the smallest number. Next measure the height at the left, center, and right side — again, the smallest wins.

Andersen’s guide adds two details worth respecting. Round down to the nearest 1/8 inch rather than up or to the nearest even number, because a slightly small window shims into place while an oversized one does not. Then check squareness: the two diagonal measurements should land within 1/8 inch of each other. Home Depot’s method matches this exactly — width at bottom, middle, top, height at left, center, right, shortest measurement each way, and trim excluded.

Skip the temptation to average the readings. An opening that bows or settles rarely averages into a good fit — it fits the smallest true dimension, so that’s the one the fabricator needs.

Check Square, Depth, And Obstructions Before Ordering

Measure the diagonals corner to corner. If they differ by more than the 1/8-inch tolerance Andersen calls for, the opening is out of square, and you should either correct it or order a custom size rather than forcing a stock unit.

Three more checks protect your order:

  • Jamb depth: measure the opening’s depth front to back. Custom fabricators commonly ask for top, middle, and bottom width and height plus the depth figure.
  • Obstructions: look inside the opening for pipes, faucets, or electrical boxes that could block the new unit’s clearance.
  • Inside and outside: on older basements or brick-furred openings, measuring both sides confirms the fit before you commit.

Lowe’s adds a practical step: open the sash and measure between the exposed jambs — width at three points between the jambs, and height from the sill to the top of the opening. That keeps the old window from hiding the true frame.

Egress Basement Windows: Code Dimensions That Override Fit

If the basement is finished or the window serves as a bedroom’s emergency exit, code rules matter more than fit. Pella’s egress guidance requires a minimum net clear opening of 5.7 square feet, with 5.0 square feet allowed at or below grade, plus at least 24 inches of clear height and 20 inches of clear width. Home Depot’s egress guide states a fully functioning opening with minimum 36-inch height and width, and adds that a window more than 44 inches off the ground needs steps or a ladder at least 12 inches wide.

Measure the opening in its fully open position for these checks — the emergency escape dimension is what the window actually clears, not its closed frame size. These figures reflect common U.S. guidance; local amendments to the International Residential Code can raise or lower them, so confirm your jurisdiction’s rules before ordering. For the actual opening, Home Depot’s basement window measuring guide walks through the same three-point method with visuals.

Measurement Where To Take It What To Record
Width Top, middle, bottom of rough opening Smallest of the three, rounded down to 1/8 inch
Height Left, center, right of rough opening Smallest of the three, rounded down to 1/8 inch
Diagonals Corner to corner, both directions Within 1/8 inch of each other = square
Jamb depth Front to back of the opening Required by custom fabricators

Insert Windows And The Order It Happens

Insert-style basement windows follow a different sequence. Remove the existing unit first, then measure the window width tip to tip, height tip to tip, and the buck frame’s drop. This differs from full replacements, where the rough opening drives the order — so know which type you’re buying before you pick up the tape.

One measurement mistake dominates basement window returns: measuring the old sash instead of the rough opening. The sash is smaller than the hole it sits in, and ordering to the sash guarantees a gap. Trim is the second classic error — it sits outside the frame and belongs nowhere in your numbers.

When your measurements are locked in, browse tested basement window screen options for the finished opening.

FAQs

Do I measure the old window or the opening?

Measure the rough opening — the bare framed hole — not the old window, sash, or trim. The old unit sits inside the opening and reads smaller. For insert windows, remove the existing unit first, then measure tip to tip.

What if the diagonals don’t match?

Diagonals differing by more than 1/8 inch mean the opening is out of square. Correct the framing before ordering, or opt for a custom-size unit. Forcing a stock window into an out-of-square opening causes binding and air leaks.

Do basement egress rules apply to every window?

Only if the space is habitable or the window serves as an emergency exit. Finished basements and bedrooms trigger egress requirements; unfinished storage areas typically don’t. Always verify local code, since jurisdictions amend the baseline rules.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.