To get 1000Hz on a mouse, open the manufacturer’s software and set the polling rate to 1000 Hz, provided the mouse supports it.
For the full breakdown, see our best 1000Hz Mouse guide.
The difference between a mouse that feels “off” and one that tracks every flick is rarely sensitivity — it’s the polling rate. To get 1000Hz on a mouse, you open the manufacturer’s software, select the device, and choose 1000 Hz from the polling-rate menu. Every mouse that officially supports the rate responds to this; the sections below cover the brand-by-brand menus and what to do when no 1000 Hz option exists.
Polling rate is how many times per second the mouse tells the computer where it is. The setting lives in the vendor’s app rather than in Windows or macOS, which is why the menu looks different for each brand.
What Does A 1000 Hz Polling Rate Actually Do?
Polling rate is separate from DPI. DPI changes how far the cursor travels per inch of mouse movement; polling rate changes how often the mouse sends position data.
Setting A 1000 Hz Polling Rate In Mouse Software
Every major gaming brand exposes the polling rate in its own application, usually in a menu labeled Polling Rate or Report Rate. The current app locations for the big names:
- Logitech — Open Logi Options+, select the mouse, and choose an available polling rate.
- Razer — Open Razer Synapse, select the mouse, go to the Performance tab, and set Polling Rate.
- SteelSeries — Open SteelSeries GG, go to Engine, select the mouse, and set the polling rate.
- Akko — Download Akko Cloud Driver or AG One NearLink Driver from the Akko download page, then set the polling rate under Performance and apply it.
The Logitech polling-rate explainer walks through this exact menu and lists the ranges each mouse supports.
| Brand | Software | Polling Rate Options |
|---|---|---|
| Logitech | Logi Options+ | 125 Hz to 1000 Hz or higher, model-dependent |
| Razer | Razer Synapse, Performance tab | Up to 8000 Hz via HyperPolling on supported mice |
| SteelSeries | SteelSeries GG, Engine | 125, 500, 1000, or 2000 Hz depending on model |
| Akko | Akko Cloud Driver / AG One NearLink Driver | Set under Performance; model-dependent |
A 1000 Hz selection in a dropdown does not guarantee a real 1000 Hz signal. The driver, USB port, and system all have to handle the higher rate, so verify with a mouse polling-rate tester after any change — the tester should show reports near 1000 Hz, not just the chosen setting. If responsiveness still feels wrong, plug the mouse into a rear motherboard USB port instead of a hub or front-panel port.
When Your Mouse Won’t Do 1000 Hz Natively
If the official app never shows a 1000 Hz option, the mouse firmware does not support it, and forcing the rate is a workaround rather than a manufacturer-supported feature. The most common unofficial route is a USB filter driver called hidusbf, hosted in the 1000hz project on GitHub.
The procedure: extract the ZIP, run 1kHz.cmd, run Setup.exe, click Install Service, select the mouse, check Filter On Device, set Refresh Rate to 1000 Hz, and click Restart. Results depend on the mouse, USB stack, and Windows configuration, and the change may need reapplying after a reboot.
Logitech’s official guidance points to Logi Options+ instead of any low-level workaround.
The working path is short: check the official app for the polling-rate menu, set 1000 Hz, then confirm the result with a tester. If the menu never appears, the mouse lacks native support, and the honest fix is new hardware — our tested roundup of the best 1000Hz mice covers models that expose the setting in the official app.
FAQs
Does a higher polling rate actually matter for gaming?
Is overclocking a mouse safe?
Can you get 1000 Hz on a Mac?
References & Sources
- Logitech. “Polling Rate on a Mouse” Explains polling-rate options and how to change them in Logi Options+.
- vadash. “1000hz” GitHub project hosting the hidusbf-based polling-rate tooling referenced in overclocking guides.
