How to Install Dash Cam Front and Rear | Wiring Made Simple

Installing a front and rear dash cam takes about an hour, starting with the front unit behind the rearview mirror, the rear camera on the rear glass, and cable routing through the headliner.

Most dual-channel kits ship with everything you need except a trim tool and a few cable ties. The job splits into three parts: mounting both cameras, hiding the connecting cable, and wiring power. Done right, neither lens shows in your sightline and the wires stay out of sight. Done wrong, you get a rattling cable or a camera that records the dashboard.

Before you begin, confirm where the rear camera cable must reach and check your vehicle’s layout. Hatchbacks and SUVs need extra care because the rear hatch moves. The basic process below works for nearly every passenger vehicle, with notes for tailgates where they matter.

Where To Mount the Front and Rear Cameras

The front camera goes high on the windshield, tucked behind or just to the passenger side of the rearview mirror. That spot keeps the lens in the wiper-swept area and blocks the least of your view. Clean the glass first with a mild cleaner, then dry-fit the mount to confirm the lens clears the frit dots, rain-sensor housing, and tint band. Those obstructions blur footage you would otherwise rely on.

The rear camera mounts at the upper center of the rear windshield. That position gives the widest, most centered view behind the vehicle. On sedans, this is straightforward. On SUVs and hatchbacks, the mount still goes high on the glass, but the cable has to follow factory paths through rubber grommets or tailgate hinge areas so it never pinches when the hatch opens.

Two placement rules matter for both cameras. Keep the adhesive off the rear defroster grid lines, and never let the rear lens sit against a tint band that degrades image quality. Adjust each mount so the horizon sits around the middle of the frame and the road is centered before you press the adhesive down firmly.

Routing the Cable Between Cameras

The rear camera cable is the hardest part of any dual-channel install. Start at the rear camera, tuck the cable along the headliner edge using a trim tool, and work it toward the front. Run it down the passenger-side A-pillar trim, then across the dashboard to the front unit or power source. Use the included cable clips or small zip ties to hold the line in place every few inches so it cannot sag or rattle.

Two rules keep this safe. Never route the cable through or near a curtain airbag, and do not let the wire cross any seat belt or moving seat track. If the cable must cross the A-pillar, tuck it behind the airbag’s deployment zone, never in front of it.

For hatchbacks and SUVs, test the tailgate before final trim reassembly. Open and close the hatch several times with the cable routed to confirm nothing pinches or stretches. Re-route through a different grommet if the factory path binds.

Power Options and Hardwiring Steps

Dash cams accept several power sources. Thinkware’s install documentation lists the 12V power cable, hardwiring through the fuse box, an OBD II cable, or a dedicated iVolt battery. Most owners start with the 12V socket, then upgrade to hardwire for a cleaner look and parking mode.

To hardwire, connect an add-a-fuse spur to a fuse slot that switches with the ignition, run the ground wire to a bare metal chassis point, and insulate every connection. The add-a-fuse taps the vehicle’s fuse box without cutting factory wiring. After connecting, confirm the camera powers on when the ignition turns and off when it shuts down. If it stays on constantly, move the spur to a different fuse slot.

Halfords’ fitting guide offers one additional step that saves frustration: test the rear camera temporarily before you hide the cable. Plug it in, power the system, and confirm you get a clear rear image with no interference, including DAB radio disruption. If you hear static or see interference, add the supplied ferrite core to the cable before final routing.

Testing Both Views Before Finishing

Before you snap any trim panel back into place, power the system and check both feeds. Aim the front lens so the road fills the frame and your hood edge sits at the bottom. Check the rear feed for a clear, centered view with no hatch or spoiler in the way. Nexar’s guide notes that rear camera detection appears in its Nexar Connect app after power-up, so verify the app lists both channels before reassembly.

Common mistakes at this stage cost the most time later: mounting the front camera too low, placing the rear camera off-center, or skipping the test run entirely. A five-minute check now beats pulling the trim apart again next week.

Once both views are confirmed, refit the trim panels, tuck any slack near the front unit, and do a final road test with a short drive. Play back a few seconds from each channel to confirm steady recording and no vibration. If your camera’s footage shows a shaky image, adjust the mount angle or tighten the adhesive base.

For those still comparing models before buying, our roundup of the best front and rear dash cams covers tested dual-channel options with parking modes and image quality comparisons.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.