How to Use Aiper Pool Cleaner | Start Cleaning in 10 Seconds

Using an Aiper cordless robotic pool cleaner requires charging the device fully, submerging it completely underwater, pressing and holding the power button for 2 seconds, and letting it descend to the pool floor, where cleaning begins automatically within 10 seconds.

One wrong sequence — activating the cleaner above water or failing to submerge it — and it won’t start. The fix is straightforward, and this guide covers every step from charging to storage, plus what to do when the battery runs low.

Step-by-Step: How to Start Your Aiper Pool Cleaner

Follow this exact order every time, regardless of which Aiper model you own.

  • Charge the battery first. Most models need at least 2 hours for a full charge. Remove the charging port cap, connect the charger, and verify the indicator shows solid green before disconnecting. The Scuba SE requires this minimum charge time; the Scuba S1 Pro follows the same rule.
  • Install or check the components. Confirm the filter basket is clean and snapped in. Attach the floating handle, brush, and swing plate if your model came with them.
  • Submerge the cleaner completely before pressing any button. An Aiper unit that activates in the air may not prime correctly. Orient the bottom toward the pool wall when lowering it in.
  • Press and hold the power button for exactly 2 seconds. The indicator light turns on. Gently release it underwater and let the device sink to the floor.
  • Wait for the 10-second delay. The cleaner pauses on the bottom, then starts its cleaning cycle automatically. If it doesn’t begin moving, lift it, submerge it again, and repeat the button sequence.

How to Choose the Right Cleaning Mode

Aiper’s models come with different mode options. The Scuba S1 Pro is the most feature-rich, offering five distinct cleaning patterns. Other models default to a single automatic cycle.

Mode What It Cleans Best For
Auto (default) Floor, walls, waterline Everyday full cleaning
Eco Floor only Light debris, runs 45 min every 48 hours for one week
Waterline Waterline tile only Targeted scum-line removal
Floor-only Pool floor exclusively Heavy debris on the bottom
Wall-only Walls in N-shaped route (skips floor) Algae or dirt on walls

Select the mode before the cleaner starts its first cycle. On the Scuba S1 Pro, press the mode button on the unit until the desired indicator lights up (check the Aiper user manual for your model for the exact sequence). Other models, like the Scuba SE, run a single automated path — press the power button and let it work.

Retrieving and Draining the Cleaner

The device stops and docks automatically when the battery runs low. Use the included retrieval hook attached to a standard pool pole. Hook the handle and lift it steadily to the edge.

Once out of the water, tilt the unit by the handle to drain all internal water before placing it on the pool deck. Water left inside can drip onto the surface and leave mineral spots or damage the electronics if the charging port isn’t sealed.

To open and clean the filter basket: press the latch on the top shell, lift the basket out, rinse it thoroughly with a garden hose, and wipe the interior cavity dry with a soft cloth. Reinstall the basket before the next use.

If you are comparing Aiper models and other cordless options before buying, our tested roundup of the best AI pool cleaners covers performance, battery life, and real-world results for each top contender.

Can You Use an Aiper Cleaner in Any Pool?

Yes, most Aiper cordless models work in both above-ground and in-ground pools. They clean floors, walls, and water lines. The Scuba S1 Pro handles pools up to 2,150 square feet, while standard models like the Scuba SE cover up to 1,600 square feet. Do not exceed the cleaner’s rated pool size — it won’t finish a full cycle before the battery dies.

The units are IPX8 waterproof, meaning they survive continuous submersion. The critical condition: the charging port cap must be fully sealed when the device is in the water. A loose cap lets moisture in and damages the internal electronics.

Common Mistakes That Stop the Cleaner From Starting

  • Incomplete submersion. The unit must be fully underwater before pressing the power button.
  • Skipping filter cleaning. A clogged basket blocks water flow and the motors may not engage.
  • Incorrect entry angle. Orient the bottom toward the wall so it sinks and rights itself.
  • Bare-hand retrieval. The exterior can be slippery and may damage seals if pulled by hand.
  • Not charging first. Even a new unit comes partially drained — charge fully before the first use.

FAQs

How long does the Aiper battery last per charge?

Battery runtime depends on the model. The Scuba S1 Pro runs up to 180 minutes per charge, while the Scuba SE lasts about 90 minutes. Actual runtime varies with cleaning mode and debris load.

Can the Aiper cleaner climb walls and the waterline?

Yes, most Aiper models climb walls and scrub the waterline automatically during a standard Auto cycle. The Scuba S1 Pro also offers a dedicated Wall-only mode and a Waterline mode for targeted cleaning.

What should I do if my Aiper cleaner won’t turn on?

First, confirm the battery is fully charged — the indicator light should show solid green. Check that the charging port cap is dry and sealed. Then submerge the unit completely and press and hold the power button for a full 2 seconds. If it still doesn’t respond, inspect the filter basket for clogs.

References & Sources

Please use a real email you check. If it's fake or mistyped, your message won't reach us and we can't reply — wrong addresses are rejected automatically.