Asphalt roofing cement is a thick, trowel-grade adhesive used to seal flashing, patch cracks, and repair minor roof damage.
For the full breakdown, see our best Asphalt Roofing Cement guide.
The stuff in that black tub is a pliable, solvent-based compound made from asphalt, fillers, and reinforcing fibers. Roofers call it roof cement, flashing cement, plastic cement, or mastic, and it has one job: sealing and patching trouble spots on asphalt-based roofing systems. It stays flexible after curing, so it moves with the roof through temperature swings without cracking. Roofing cement is a repair tool, not a primary waterproofing membrane — understanding what it can and cannot do keeps you from using it as a cure-all for serious roof failure.
What Is In Roofing Cement, And How Does It Work?
Roofing cement is a cutback product, meaning solvents thin the asphalt so it applies smoothly and then evaporate as the material cures. A typical formulation runs roughly 40% to 60% asphalt, 20% to 30% solvent, and 10% to 20% inert mineral fillers, though exact ratios vary by brand. Some products add reinforcing fibers for extra strength.
The result is a sticky, cohesive sealant that bonds to asphalt shingles, built-up roofs, metal flashing, and masonry. It is designed to remain pliable rather than harden, which lets it absorb the expansion and contraction of roof materials through heating and cooling cycles. Most products cure to the touch in 24 to 48 hours when applied in a thin layer, typically about 1/8 inch thick.
Types Of Roofing Cement And What Each One Does
Two ASTM standards govern roofing cement in the United States. The older ASTM D2822 covered formulations that could contain asbestos; the current ASTM D4586 standard applies to asbestos-free products, which is what essentially all modern U.S. roofing cements are. The D4586 standard defines two types with different jobs:
- Type I (plastic cement): A self-sealing, adhesive, ductile asphalt compound used for general patching, sealing cracks, and bonding materials on flat and low-slope surfaces.
- Type II (vertical-grade flashing cement): A stiffer formulation with a higher softening point, made for vertical surfaces and flashing details where the material must resist sagging and flow in summer heat.
You will also see wet/dry formulations on store shelves. Products like APOC 109 RAIN-PROOF Wet/Dry Roof Cement are designed to adhere to damp surfaces, while standard formulas require dry conditions. Check the label before applying — using a dry-only product on a wet roof is a common mistake that produces a weak bond.
What Can Roofing Cement Fix, And Where Does It Fail?
Roofing cement is the right tool for small, localized repairs: patching splits and cracks in composition shingles, sealing flashing laps and roof penetrations, and fixing seams on built-up or mineral-surfaced roofs. It also works as a bonding agent for re-adhering loose shingle tabs. Black Jack’s All-Weather Roof Cement, for example, is a pliable product usable on damp and dry surfaces for exactly these jobs.
The hard truth: roofing cement will not fix a failing roof. Do not use it on large leaks, rotten decking, extensive membrane failure, or structural problems — those need real repair, not a patch. It also is not universally compatible with every roof system; some modern membranes and coatings react poorly to solvent-based products. When a product datasheet specifies compatible surfaces, follow it.
How To Apply Roofing Cement Correctly
Application is straightforward if you prepare the surface properly:
- Clean the area of loose debris, old sealant, and moisture (unless using a wet/dry formula).
- Spread a thin layer about 1/8 inch thick with a trowel, pressing firmly to work it into cracks and seams.
- Smooth the surface so water sheds rather than pools, leaving no gaps or thin spots.
- Allow 24 to 48 hours to cure before exposing the repair to heavy traffic or weather.
For vertical flashing repairs, use a Type II vertical-grade cement, which stays put instead of slumping. And remember the safety basics: these are solvent-based products, so read the label and SDS, work in a ventilated area, and keep them away from open flames.
Confusing roofing cement with paving asphalt cement is easy — the names sound similar — but they are completely different materials. Paving asphalt is the binder for road asphalt concrete; it has no business on your roof. If you are ready to buy the right product for your repair, our tested roundup of the best asphalt roofing cements covers the top performers for every job.
References & Sources
- ASTM International. “ASTM D2822-05: Standard Specification for Asphalt Roof Cement.” Historical standard covering asbestos-containing formulations and two types/classes.
- U.S. Federal Highway Administration. “Asphalt Cement vs. Roofing Cement: A Distinction.” Clarifies the difference between paving binder and roofing sealant.
- Lowe’s. “APOC 109 Rain-Proof Wet/Dry Roof Cement — Product Data Sheet.” Documents wet/dry application capability and typical use cases.
